11
WARNING:
TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE SERVICING.
TOOL REQUIRED: FLATHEAD AND PHILLIPS SCREWDRIVER
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK - UNPLUG CLEANER BEFORE REMOVING OR
REPLACING LIGHTBULB.
This cleaner uses a common automotive lamp #906, 13.0 volts. For bulb replacement call 1-800-321-1134
or your local auto parts store.
LIGHTBULB: REMOVAL & REPLACEMENT
GENERAL MAINTENANCE
Lean cleaner handle
back. Remove the one
(1) screw.
Using the end of a
Flathead screwdriver,
gently pop open the
lens. Remove lens.
Pull bulb of of socket.
Do NOT twist. Gently
push bulb into socket to
replace.
Snap lens back into
place. Secure the head-
light lens by replacing
the one screw.
1.
2.
3.
4.
1. Check to see if dirt container is full; empty
if needed.
2. Plug cleaner in and check to see if there is
any suction at end of hose. If there is
suction
at end of hose, move on to Diagram 4. If there
is
no suction
at the end of hose, follow these
steps: 1. Unwrap hose from caddy. Remove
obstruction. Check access door on back of
cleaner (near hose wand). Remove three (3)
screws and check for obstruction (Diagram 1).
2. Remove dirt container (Pg. 8) and check dirt
container inlet located on cleaner (Diagram 2).
3. Remove nozzle guard (see Diagram 3) by
removing the three (3) screws. Remove
obstruction.
3.
To reassemble, be sure tabs
are engaged. Pivot the lower
housing closed.
Pivot lower housing and
remove clog.
5.
1.
2.
Rotate locking ring 180˚ and
turn Power Brush Tool over.
4.
LOCKING RING
DEBRIS REMOVAL/
NOZZLE GUARD
6.
DEBRIS REMOVAL/POWER BRUSH TOOL
DEBRIS
REMOVAL/HOSE
WARNING:
TO REDUCE RISK OF PERSONAL INJURY - UNPLUG CLEANER BEFORE SERVICING
12
ANY OTHER SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE
CUSTOMER SERVICE (1-800-321-1134)
In the event that further assistance is required, see your Yellow Pages for an authorized Royal
®
Dealer. Costs of any
transportation to and from any place of repair are to be paid by the owner. The service parts used in this unit are
easily replaced and readily available from an authorized Royal
®
Dealer or retailer. Always identify your cleaner by
the model number and manufacturing code when requesting information or ordering replacement parts. (The model
number appears on the bottom of the cleaner.)
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE REASON
POSSIBLE SOLUTION
Cleaner won’t run
Cleaner won’t
pick-up or low
suction
Dust escaping
from cleaner
Cleaner tools won’t
pick-up
Headlight not
working
Cleaner is difficult
to push or won’t
move forward
1. Power cord not firmly plugged into
outlet.
2. Blown fuse or tripped breaker.
3. Needs service.
4. Thermal Protector activated.
1. Dirt container not installed correctly.
2. Dirt container full.
3. Brushroll worn.
4. Broken or worn belt.
5. One or both filters are clogged.
6. Nozzle/dirt passage clogged.
7. Carpet height setting is incorrect.
1. Dirt container full.
2. Dirt container not installed correctly.
3. Hose not installed correctly.
4. Filter not installed completely.
1. Hose clogged.
2. Dirt container full.
3. One or both filters are clogged.
1. Bulb burnt out.
2. Loose electrical wires.
1. Carpet height setting is incorrect.
1. Plug unit in firmly.
2. Check fuse or breaker in home. Replace
fuse/reset breaker.
3. Take to service center or call 1-800-321-1134.
4. Allow cleaner to cool - Pg. 3.
1. Review dirt container removal and replacement -
Pg. 8 & 9.
2. Empty dirt container - Pg. 8.
3. Replace brushroll - Pg. 10.
4. Replace belt - Pg. 10.
5. Remove both filters and clean - Pg. 8 & 9.
6. Open access door; remove obstruction - Pg. 11.
7. Set carpet height adjustment to appropriate
setting for carpet being cleaned - Pg. 7.
1. Empty dirt container - Pg. 8.
2. Review dirt container removal & replacement -
Pg. 8 & 9.
3. Review hose installation - Pg. 6.
4. Review filter removal & replacement - Pg. 8 & 9.
1. Remove hose and tools; remove obstruction -
Pg. 6 & 11.
2. Empty dirt container - Pg. 8.
3. Remove both filters and clean - Pg. 8 & 9.
1. Replace bulb - Pg. 11.
2. Call 1-800-321-1134 for nearest authorized
Royal
®
Dealer.
1. Set carpet height adjust lever to appropriate
setting for carpet being cleaned - Pg. 7.
