background image

Quick Reference Guide

DBALL2-GM9 Range Extender Ready (RXT) Installation

© 2017 Directed. All rights reserved.

* Your factory or aftermarket remote may differ from the model shown in the 

illustrations.

Pit Stop Mode

The Pit Stop Mode feature is practical when you need to stop and run an errand, 
but wish to keep the engine running.

Vehicle Takeover with Get In and Go*

4

3

1

Close 

the vehicle doors, hood and trunk, then press 

the Remote Start button on the transmitter to start 
the vehicle.**

2

Press

 the brake pedal, put the car 

in gear and drive off.

Enter

 the vehicle, while making sure the 

factory remote is inside with you.

Press 

the Unlock button on the factory 

or aftermarket remote.**

Ready to 
drive off

Press 

remote start 

button**

Press Unlock 

button on 

either remote**

OR

** Your aftermarket remote may differ from the model shown in the illustrations.

GG

Get In and Go

 connections required. 

Get In and Go

Get In and Go is designed to provide users with easy takeover when 
entering their Push-to-Start (PTS) equipped vehicle, once it has been 
remote started. 

Typically, users would have to remote start their vehicle, then get inside and press 
the vehicle start button to perform a takeover. There is therefore a physical action 
required to drive away. With Get In and Go technology, you simply remote start the 
vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and 
enjoy your vehicle.

This unique feature monitors a variety of parameters such as the key fob, vehicle 
speed sensor and door sensor, in order to perform takeover securily.

GG

Complete the following steps within 45 seconds
or the vehicle will shut down.

1

2

3

Stop the vehicle in a safe parking spot 
and put the gear in Park (P).

Press 

remote start 

button* 

Stop & put vehicle in Park (P)

P

&

Note: 

We recommend that you always lock the doors 

of your vehicle when leaving it unattended.

It is now safe to leave the engine running and exit the 
vehicle with the factory remote in hand.

Press

 the button to remote start the vehicle.*

Exit vehicle with 

Smart Key

Enter vehicle with 

factory remote*

Summary of Contents for XPRESSKIT GM9

















Reviews: