background image

3

Directed Digital System MIT4

© 2015 Directed. All rights reserved.

Warning! Safety first

The following safety warnings must be observed at all times:

•  Due to the complexity of this system, installation of this product must only be performed by an authorized 

Directed dealer.

•  When properly installed, this system can start the vehicle via a command signal from the remote control.  

Therefore, never operate the system in an area that does not have adequate ventilation. 

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
•  Never use a test light or logic probe when installing this unit. Always use a multimeter. 
•  Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). 
•  When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the 

remote start system must be disabled using the installed toggle switch. It is the user’s sole responsibility to 
properly handle and keep out of reach from children all remote controls to assure that the system does not 
unintentionally remote start the vehicle.

•  USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT 

TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR 
PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, 
personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never 
remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the 
ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein 
the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized 
Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle 
starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS 
INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS 
MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT 
AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD 
RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing 
to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and 
with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. 

This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. 
Installation in such vehicles may pose certain risk.

Summary of Contents for MIT4































Reviews: