9
Directed Digital System MIT4
© 2015 Directed. All rights reserved.
Type 3
Refer to "Vehicle wiring reference charts" on page 11 for more information on vehicle-specific connections.
2 & 8:
White/Brown:
(+) 12V
16 Black
3 Wh
4 White
12 White
4 Red
7 White
2 Wh
2 Bk
6 Gr
een
18 White
Manual/Auto. Transmission Type
Prog.
Button
Manual/Auto. Transmission Type
Prog.
Button
9:
Black
: (-) Ground
10:
Red
: (+) 12V
1 & 7:
White:
(+) Parking Lights
HS CAN Low:
Tan
: 4
HS CAN High:
Tan/Black
: 5
[1]
(-) Hood Input:
Gray
: 3
(-) Unlock/Disarm Output:
Dk. Blue
: 7
(-) Lock/Arm Output:
Dk. Green
: 15
The Remote Start
Safety Override
Switch
MUST
be in
the ON position.
Remote Start Safety
Override Switch
[2]
(+) Siren Output:
Brown
: 17
All adapters are displayed from the wire side (unless specified otherwise).
3
1
2
4
5
6
7 White
4 White
8 thick-gauge wir
es
MC501
(+) Accessory 1 Output:
Orange
: 5
(+) Accessory 2 Output:
Orange
: 5
(+) Ignition Input/Output:
Pink
: 3
(+) 12V Input:
Red
: 4
(+) 12V Input:
Red
: 6
[3]
Starter Input (Key Side):
Green
: 7
(+) Starter Output (Car Side):
Violet
: 8
(+) Ignition:
Red or
Black/White
, pin 2
(+) 12V:
Blue/Yellow
, pin 1
(-) Driver Door Trigger:
Lt. Green
, pin 6
(+) Starter:
Black/Yellow
, pin 5
(+) Accessory 1:
Blue/Red
, pin 4
(+) Accessory 2:
Blue/Black
, pin 6
C-204 White Connector
(Front of Junction Block.
at Driver Kick Panel)
Junction Block
front view
Junction Block
rear view
(Driver Kick Panel)
Hood Pin
HS CAN High:
Red,
pin 6
HS CAN Low:
Black
, pin 14
OBDII
Diagnostic Connector
under Driver Dash
(connector side view)
16
8
9
1
7
6
5
13
14
15
12
4 3 2 1
8
9
10
11
C-204
(-) GWR Output:
Blue/White
: 18
Clutch:
Brown/Black
,
pin 2
For Manual Transmission ONLY
Clutch
Pedal
2
1
Relay pin 30
Relay pin 87a
30
86
85
87
87a
Cut
(-) Auto Headlamp Shutoff:
Green/Black
: 10
[2]
The siren is
only
compatible with hybrid systems.
[1]
The installation of an aftermarket hood pin is
only
required on vehicles
that are
not
equipped with a factory hood pin.
[3]
The green wire is only required for starter kill and antigrind connections.
Ignition Switch Connector
(left side of steering column)
(+) Parking Lights:
Green/White
, pin 2
C-208 White Connector
(Junction Block at Driver Kick Panel)
1
2
3 4
8 9 10 11
5
12
13
6
14
7
15
(-) Lock/Arm:
Lt. Green/Black,
pin 22
(-) Unlock/Disarm:
Red/Green
, pin 5
C-217 White 24-pin Connector
(Rear of Junction Block,
at Driver Kick Panel)
5
4
3
2
1
10 11 12
15
14
13
16 17 18
22
23 24
19 20 21
7
6
8 9
Solder onto a diode, cut away the unneeded
Empty pin
Diode
Solder the wire to secure it on the metal pin.
This part can be removed
because only the metal pin is
Unlock* wire from Remote Starter
*Lock: Same procedure have to be done for missing Lock wire.
If there’s no Lock/Unlock wires, you can either insert
Lock/Unlock wires directly as shown below or use
Installation Type 4
on page 10.
Siren
