background image

22

©

2004 Directed Electronics, Inc.

The Valet

®

Take-Over feature allows the vehicle to remain running

after the key has been removed from the ignition. This feature is

useful for occasions when you wish to exit and lock the vehicle for

short periods of time, but would like to leave the motor running

and the climate controls on. 

To perform Valet

®

Take-Over:

1.  Before turning off the engine, press and release 

on the

transmitter twice (or press and release the optional momen-

tary switch twice).

2.  Turn the ignition key to the OFF position. (The engine will

stay running.)

3.  The engine will run until the pre-programmed time elapses or

a shut-down input is received. (See the previous Remote Start

section for a complete list of shut-down inputs.)

NOTE: 

This feature will not work if the brake pedal is being pressed.

Short run turbo mode keeps the engine running after arriving at

you destination for a programmable period of 1, 3, 5 or 10 min-

utes. This allows the system’s timer to conveniently cool down the

turbo after you have left the vehicle. 

To activate:

1.

Park the vehicle and set parking brake. 

2.

Remove your foot from the brake pedal and leave the engine

Short-Run/Turbo

Valet

®

Take-Over

Summary of Contents for Cyber 125xv







































Reviews: