© 2004 Directed Electronics, Inc. Vista, CA
3
37
7
2
2 TTA
ACCH
H W
WIIR
REE SSEEN
NSSEE//V
VO
OLLTTA
AG
GEE SSEEN
NSSEE:: If the tachometer signal wire is used, this feature must be left in the default
(tach wire connected) setting. If programmed to the voltage sense setting, the unit will crank the starter for a
preset time that can be programmed in Feature 5. Once the starter has been engaged, the system will check the
voltage level to verify the engine is running. The threshold for the voltage level test can be programmed in
Feature 6. When using voltage sense mode, connection of the H2/5 VIOLET/ WHITE tachometer input is not necessary.
3
3 R
RU
UN
N TTIIM
MEE 1
12
2//2
24
4//6
60
0 M
MIIN
NU
UTTEESS:: This feature controls how long the engine will run before it “times out” and
shuts down. Programmed to the default setting the engine will run for 12 minutes. If the 24 or 60 minute run
time is desired, change this feature to the two or three flash setting.
4
4 P
PA
AR
RK
KIIN
NG
G LLIIG
GH
HTTSS FFLLA
ASSH
HIIN
NG
G//CCO
ON
NSSTTA
AN
NTT:: In the default setting, the unit will flash the vehicle’s parking lights
while remote started. The constant setting will turn the parking lights on solidly for the entire run duration.
5
5 CCR
RA
AN
NK
K TTIIM
MEE 0
0..6
6//0
0..8
8//1
1..0
0//1
1..2
2//1
1..4
4//1
1..6
6//1
1..8
8//2
2..0
0//4
4..0
0:: If Feature 2 is programmed to the voltage sense setting,
the crank time must be set to the appropriate duration. The default setting is 0.6 second. If a different crank
time is desired, select Feature 5 and (while pressing the Program switch) press the Channel Two button to
advance through the LED Off settings. The unit will flash the LED to indicate which time is selected. Once the
4.0 second setting is reached the next press of the Channel Two button will reset the system to the shortest
setting.
6
6 V
VO
OLLTTA
AG
GEE CCH
HEECCK
K LLEEV
VEELL H
HIIG
GH
H//LLO
OW
W:: This feature only functions when Feature 2 is programmed to voltage sense.
Some vehicles have many accessories, which are turned on when remote started. In these vehicles, the variation
of voltage between the engine off and the vehicle running is very slight and the remote start unit may “think”
the vehicle has not started. This can cause the remote start to shut down after the vehicle has been started. If
this is the case, program this feature to the LOW position.
7
7 SSH
HO
OR
RTT R
RU
UN
N ((TTU
UR
RB
BO
O TTIIM
MEER
R)):: When the
and
buttons on the transmitter are pressed simultaneously
while the engine is running, the vehicle will continue to run for the short run time. The factory default is 1
minute.
8
8 A
ACCTTIIV
VA
ATTIIO
ON
N P
PU
ULLSSEE CCO
OU
UN
NTT:: This feature allows the number of pulses to activate the remote start feature to be
changed from 1, 2, or 3 pulses. The pulse count programmed to start the vehicle will also be the same required
to shut down the remote start.
9
9 2
2n
nd
d IIGGNNIITTIIOONN//AACCCCEESSSSOORRYY OOUUTTPPUUTT:: This will allow the PINK/WHITE to be used as a 2nd ignition or a
2nd accessory.
1
10
0 A
ACCCCEESSSSO
OR
RY
Y SSTTA
ATTEE D
DU
UR
RIIN
NG
G W
WA
AIITT--TTO
O--SSTTA
AR
RTT:: This will allow the programming of the accessory wire during the
wait-to-start period of a diesel motor. When ON the accessory comes on when the wait-to-start output is acti-
vated and stays on, dropping out during crank and returning once the car has started. When OFF the accessory
will activate as a normal accessory.
