background image

Operating Instructions UVD 170S/340S 

 

 1

1 Introduction 

1.1 Unpacking 

 

To unpack the unit, proceed as follows: 

• 

Place the box on the floor and remove the accessories pack. 

• 

Pull out the unit, slowly and carefully, using the two foam inserts. 

• 

Remove the polythene packaging by placing the unit on a firm base and lifting at one side, 
then the other, while drawing the packaging out from underneath it. 

  

 

  

Please note:

  Retain all original packing materials in a safe place. It is the optimum 

packaging for shipping the unit (e.g. for repair). Shipping of the unit in 
any other packaging automatically nullifies the warranty. 

 

• 

Check-off the contents of the accessory pack against the list in section "Standard 
Accessories UVD 170S/340S"
, page 24) 

1.2 Warranty 

 

The standard warranty coverage for this unit is in accordance with the conditions of sale. The 
warranty has a duration of one year from invoice date and covers materials and labour, ex-
works. Please note that wear-parts (i.e. needle, needle-seat, syringe and valve-seals) cannot be 
covered by the warranty. 

The warranty period for the deuterium lamp is six months from delivery date (see the label at 
the lamp cable). Removing this label automatically invalidates the warranty coverage.

 

For 

lamps with timer (without the above label) the warranty period is 1000 operating hours. 

The warranty does not extend to the flow cell. 

The warranty coverage shall become invalid in any case identified as resulting from 
inappropriate use, service or the implementation of non-specified spare parts. Similarly, the 
warranty coverage shall be invalidated in the event of inappropriate shipment, packaging or 
failure to remove aggressive or damaging solvent residues. 

1.3  How to Use This Manual 

 
The layout of this manual is designed to provide quick reference to the appropriate sections, 
according to the operation required. 
 
However, it is recommended that, before operating the 

UVD 170S/340S

, the manual should 

be read thoroughly and completely in order to obtain a full understanding of the instrument. 
 

Summary of Contents for UVD 170S





























Reviews: