DINSEO DIX TIG GO 1806.M AC/DC, Operation Manual, Page: 20 / 30

20
5B) BALANCING the AMPLITUDE of the CURRENT (I) (-50÷+20)
It is possible to adjust the amplitude of the current (I) while the
electrode stays in place independently, using positive or neg-
ative values, guaranteeing perfect control of penetration and
cleanliness, drastically reducing side incisions.
Display - +
-50 150% 50%
I (A)
t (s)
Display - +
0 100% 100%
I (A)
t (s)
Display - +
+20 80% 120%
I (A)
t (s)
Press the BALANCING and FREQUENCY (T4) key once, wait
a few seconds, and hold the same key down for at least
2 sec-
onds. Then use the ENCODER Knob (E) to adjust the value
shown on the DISPLAY (D).
I 1
PULSE
SYN
FAST
SLOW
WAVE
Ø
DIX TIG GO
1806.M
I
1
SYN
FAST
SLOW
VRD
HF AC
DC
DC
HF
HOT
START
ARC
FORCE I
b
T
b
T
p
f
I
p
I
2
MEM
PRG
PULSE
PULSE
ULTRA
FAST
WAVE
WAVE
A
V
SWITCH
SWITCH
D
T4
E
LED L30 flashing intermittently.
To exit, simply push the BALANCING and FREQUENCY (T4)
key again (BALANCING LED off).
5C) BALANCING (BALANCE PLUS)
It is possible to adjust the time (t) and amplitude of the cur-
rent (I) while the electrode stays in place simultaneously and
independently, using positive or negative values, guarantee-
ing perfect control of penetration and cleanliness, drastically
reducing side incisions.
For simultaneous setting of the parameters, following the in-
structions given in points 5A and 5B in succession, with the
help (if necessary) of the example shown below.
Display - +
t -15 65% 35%
I -20 120% 80%
I (A)
t (s)
6) FREQUENCY CONTROL IN AC (40 ÷ 250 Hz)
This controls the frequency for the various wave shapes, for
better directional control, reducing the thermally altered area,
with greater penetration and lower electrode consumption.
The high frequency makes it possible to weld very small thick-
nesses with excellent results, while the low frequency is ideal
for welding average thicknesses, or where edge preparation
is poor.
I (A)
t (s)
I (A)
MIN 40 Hz MAX 250 Hz
t (s)
To regulate the FREQUENCY push the BALANCING and
FREQUENCY key (T4) twice (FREQUENCY LED flashing)
and use the ENCODER Knob (E) to regulate the value indi-
cated on the DISPLAY (D).
I
1
PULSE
SYN
FAST
SLOW
WAVE
Ø
DIX TIG GO
1806.M
I
1
SYN
FAST
SLOW
VRD
HF AC
DC
DC
HF
HOT
START
ARC
FORCE
I
b
T
b
T
p
f
I
p
I
2
MEM
PRG
PULSE
PULSE
ULTRA
FAST
WAVE
WAVE
A
V
SWITCH
SWITCH
T4
E
D
To exit, simply push the BALANCING and FREQUENCY (T4)
key again (FREQUENCY LED off).
7) Press the WELDING MODE SELECTION Key (T9) and go to
one of the 4 options available:
L5 2T
L6 4T
L7 SWITCH
L8 SPOT WELD
8) By pushing the WELDING PARAMETERS SE-
LECTION key a number of times it is possible to
set the various TIG WELDING PARAMETERS
(see the “TIG AC and DC Welding” paragraph -
WELDING PARAMETERS).
9) Once the all the selections/regulations indicated
above have been made, welding can begin.
10) During the welding process the DISPLAY shows the real Amps
(A) at which the operator is actually welding.
T9
L5
L6
L7
L8
SWITCH