1.
Do not at tempt to heat a Sm a rt • Th e rm base in coo k top mod e.
2. Do not at tempt to heat a Sm a rt • Th e rm base without base locato r.
INFO:
If there is no heating for more than 30 seconds,
the power level will revert to the minimum power level 1.
3. If machine is idle for more than 3 minutes, the charger
will revert back to Smart•Therm™ mode.
4. If a Dinex® base is placed correctly on the charger
while in cooking mode, the charger will revert back to
Smart•Therm™ mode and proceed to automatically
heat the base to the required temperature.
5. Each evening before you close your operation, turn off
all Smart•Therm™ chargers by depressing the “ POWER”
button. All membrane panel LED’s will turn off.
INFO:
The cooling fan will continue to run and will turn off
approximately 20 seconds after the power is turned off.
The unit will “auto-reset” when the power is turned off. The
fan will cycle and all 10 lights will flash.
Page 4
S M A RT•THERM™ CHARGER CLEANING INSTRU C T I O N S
1 . Unplug the charger be fo re cleaning. Do not submerge the
c h a rger in wate r. Do not splash or pour water onto the
c h a rg e r’s co nt rol panel or into int a ke/outlet ve nt s. Po s s i b l e
s h ock hazard may result and the charger may be damaged.
2. The coo king surf a ce is a mate rial similar to te m p a red glass.
Please use appro p ri ate ca re in handling and cleaning.
cooktop. To get into cook mode, first remove the base
locator by lifting it straight up off the charger. Failure to
remove this may cause melting or other damage to it.
While charger is OFF, press the “POWER” button 3 times
within 10 seconds to activate Cook mode. The charger will
beep once to indicate it has entered the cooking mode.
When first entering cooking mode, it will be at minimum
power, so one(1) red LED will be lit. If you are in Smart-
Therm mode, no red LED's will be lit unless there is a valid
base charging on the charger. Use the up and down arrow
buttons to adjust the power level in 10% increments of
max power. The red LED’s will light climbing from left to
right with each press of the up arrow. Full power is indi-
cated by having all ten(10) LED’s lit. Pressing the down
arrow will turn off the LED’s from right to left and reduce
the power.
3. Do not use steel wool or abra s i ve cleaners or chlori n ate d
cleaners on the charger.
4. Wi pe the ent i re charger off with a damp cloth and mild dete r-
g e nt . Dry the charger be fo re co n n e cting it to its elect ri cal source
WARNING:
Never spray,wash or use exce s s i ve wa ter on the
Sm a rt • Therm induction charg e r.Be fo re cleaning it is absolute ly
n e ce s s a ry to unplug power plug.
• Do not use the cook-top if glass is broken or if
anything melts onto it.
• Always use approved coo kwa re when in coo k top mod e.
• Never use the coo k - top as a work surf a ce or cutting bo a rd.
• Never attempt to cook food dire ct ly on the glass surf a ce.
• Never attempt to heat aluminum fo i l .
4.
AFTER WASHING SMART•THERM™ BASES, STORE IN
DINEX® DRYING RACK.
• IBDRS/90 - HOLDS 90 INDUCTION BASES
• IBDRS/180 - HOLDS 180 INDUCTION BASES
• IBDRS/270 - HOLDS 270 INDUCTION BASES
Maintenance
!
!
!
Smart•Therm
™
charger
locator
Troubleshooting
IMPORTANT:
Safety-relevant parts should be replaced
with original factory parts only. Any defective parts must
be removed and replaced by a qualified service technician
authorized by Dinex®. Should you require service please
call the Dinex Hotline at 1-888-673-4639. In order for the
warranty to remain valid, work must be authorized by
Dinex® prior to being performed.
The Dinex® Smart•Therm™ Charger is a very intelligent
device. Built in diagnostics can help you to determine the
cause of most problems. The following section explains
how to determine if you are experiencing a problem and
what can be done to correct the problem. This informa-
tion can be very helpful if you are calling our Customer
Service department to report any operational difficulties.
1. Errors are indicated by a number of consecutive audible
“beeps” and the repeated flashing of the center 6
red lights.
2. If an error occurs, remove the base from the charger and
turn the charger OFF, wait 5 seconds, and turn the
charger back ON.
3. When the green “POWER” LED illuminates, place the
base back on the charger to continue charging.
4. If an error persists, remove the base from the charger,
turn the power off and unplug the charger, with the
charger unplugged press the “POWER” button (panel
LED’s may momentarily flash), wait 5 seconds and then
plug the charger back in and turn the charger on by
pressing the “POWER” button.
5. When the green “POWER” LED illuminates, put the base
back on the charger to continue charging. Make sure
that the base is properly positioned on the charger.
!