2. The Sm a rt • Th e rm™ Ch a rger is turned on by pressing the
g reen “ P OW E R” b u t ton on the left fro nt of the membra n e
panel. A green LED will illuminate indicating that the
Smart•Therm™ Charger is turned on and ready for use.
3 . Be sure base locator is placed on the Sm a rt • Th e rm ™
Ch a rger pro pe rl y.
4 . Pl a ce a Di n ex® Sm a rt • Th e rm™ base on the Sm a rt • Th e rm ™
Ch a rg e r. The charger will beep once as it re cog n i zes the base.
5. Red LED(s) will illuminate indicating that the base is
c h a rg i n g.
Do Not Remove
the base while the red LED(s)
a re in prog re s s i o n . As the base charg e s, the red LED(s)
will light prog re s s i vely to the ri g ht until all 10 are lit. If the
base is re m oved be fo re all 10 are lit, it will not be fully
c h a rged resulting in a lower delive ry te m pe rat u re.
INFO:
You will hear three loud “BEEPS” if you remove the
base before it is fully charged.
6. If no red LED’s illuminate, re m ove and re position the base.
7. After all 10 LED’s light, they will all flash and the charger
will beep indicating that base is at the full temperature.
Charge time for a base will be approximately 13 seconds
for 611240, 15 seconds for 611208, 17 seconds for
611220 @ 240V, 20 seconds @ 208V, or 30 seconds
for 611120 (120V), depending on the residual energy in
the base. Voltages lower than those listed will increase
changing time.
INFO:
Fluctuation in voltage may affect cycle heating time.
8. When the heating cycle is complete, the 10 LED’s will
flash and an audible signal will indicate that the base
has completed its cycle.
9. I m m e d i ately place another base on the Sm a rt • Th e rm ™
Ch a rger making sure that the red LED(s) illuminate. If the
base is alre a dy partially charged the cycle time will be
re d u ced acco rd i n g l y. The number of LED’s will indicate the
i nte rnal level of late nt heat or charge re m a i n i n g. Fo r
ex a m p l e, if 4 LED’s are lit, the base will re q u i re only 6 more
l i g hts to co m p l e te the cycle time for a full charg e.
10. If the charger sees no activity for an extended period of
time, it will beep 2 times and go into “Sleep” mode to
conserve power. This will be indicated by the red LED’s
scrolling across the display. Press any button to restart
normal operation.
11. The Smart•Therm™ Charger has an auto-shutoff fea-
ture that will turn off the machine after it has been idle
for a period of time. The charger can also be turned off
manually by depressing the “power” button.
INFO:
The cooling fan will continue to run and will turn off
approximately 20 seconds after the power is turned off.
Smart•Therm™
c
harger
s
have
an
auto-reset feature that is
activated when the unit is turned off. Upon turning the unit
off, the fan will cycle on, all lights will flash, and it will then
turn off.
COOKING MODE (611120 & 611220 ONLY!)
WARNING:
Do not heat Smart•Bases in cooktop mode.
Doing so will void warranty. Always use the Base Locator
when heating Smart•Bases.
The Smart•Therm™ Charger will power up by default in
the Smart•Therm™ mode. If your charger is equiped with
the cooktop feature, you can also use the charger as a
Page 3
4. Do not place foreign objects on the charger, or between
the Dinex® base and locator. Foreign objects may over-
heat and cause damage to the charger and/or base.
5. Do not use any Smart•Therm™ Charger that has a dam-
aged cord or plug. Consult the warranty and follow
instructions for service.
6. Do not let the charger cord touch hot surfaces.
7. The center of the charger top may get hot to the touch
after hours of continuous use. Use caution when load-
ing and unloading bases.
8.
A dedicated electrical circuit is recommended for
EACH Smart•Therm™ Charger.
IMPORTANT:
Every installation site has different electrical
wiring requirement. Because many different local codes
exist, it is the owner and installer’s responsibility to comply
with all federal, state and local codes. Dinex® is not respon-
sible for any consequential damages, either expressed or
implied, as a result of failure to comply with installation
requirements.
WA R N I N G :
Please do not attempt to open the charger or pe rform
s e rv i ce of any ki n d. This prod u ct can only be serv i ced by a Di n ex ®
Au t h o ri zed Se rv i ce Agent or designated Di n ex® pe r s o n n e l .Co n t a ct
Di n ex® at 1-888-673-4639 for serv i ce info r m a t i o n .
WARNING:
Any installation not matching the require-
ments discussed in this manual will automatically void
the product’s warranty.
INSTALLATION
1. The Smart•Therm™ Charger can be installed on top of a
flat, level countertop or shelving, being careful to main-
tain at least two inches of clearance on all sides of the
charger for cooling. Do not place over paper or
loose material. That may inhibit air flow.
Dinex® Induction Stand
(Assessory product)
ICSTANDM (Mobile with casters)
ICSTAND (Not mobile)
2. The charger must be plugged into a grounded 120V,
208V or 240V (depending on the model purchased), sin-
gle-phase receptacle. Check rating base on the charger
to verify correct voltage.
IMPORTANT:
Each charger should be connected to its own
dedicated circuit. They should not be connected to circuits
sharing compressors or other heavy current draw devices.
(i.e. plate heaters, steam tables, etc.)
3. Do not move the Smart•Therm™ Charger when it is
electrically connected.
SMART•THERM™ MODE
WARNING:
Do not heat Smart•Bases in cooktop mode.
Doing so will void warranty. Always use the Base Locator
when heating Smart•Bases.
1. Make sure that your Smart•Therm™ Charger is plugged
into an energized circuit as described in the previous
section. This should be a dedicated circuit, not shared
with any devices utilizing motors, compressors, or com-
ponents requiring a heavy current draw.
Operation Instructions
!
!
!
!
!
!
!
!
!