background image

10

NOTE:

Your heater may produce some noise during 
operation. This noise is caused by the expansion 
and contraction of the element as it changes 
temperature, and is normal for this type of 
product. Whilst the noise produced is usually 
very quiet, certain environmental factors can 
make it more noticeable, such as hard fl ooring 
or minimal furnishings If you believe that the 
expansion noise is excessive, please contact us.

NOTE:

Should the heater fail to operate, 
this may be caused by the room 
temperature being higher than the 
thermostat setting.

The heater controls can be easily adjusted by using the six buttons on the User

Interface.

1.

  

The Home Screen

 shows the options available at each stage 

of adjustment. Here the current target temperature (setpoint) 

is displayed along with the mode of operation. Any use of the 

Advance function will be displayed here, and pressing Enter 

will show the functions which are enabled.

The currently active mode of operation is displayed at the top of 

the screen e.g. ‘

Out All Day

’ timer.

When  the  heater  is  trying  to  achieve  or  maintain  a  room 

temperature, ‘

Heating On

’ will be displayed, otherwise, ‘

Heating Off 

‘ will be displayed.

When the controller buttons have not been pressed for a long period of time, the display will ‘sleep’ and the text 

will disappear. The heater is still on and active in whatever Mode it was set to.

2.

 

Menu

  - Displays the Main Menu;

Boost

 – Activate Boost Mode

Modes

 - Set the mode of operation.

Settings

 – Time/Date, Temperature units etc.

3.

 

Back

 returns to the previous screen.

4.

  The 

Up

 and 

Down

 buttons are used to navigate through the menus and adjust the required room temperature 

on the main screen. The screen colour changes based on the temperature selected, showing deep blue through 

to bright red.

5.

 

Enter

 is used to enter sub menus and to confi rm actions.

6.

  The 

Advance

  button  is  only  used  when  a  Timer  Mode  is  active,  it  allows  the  timer  schedule  to  be  changed 

temporarily by forcing a 

Heating On

 period to begin or end early. For more information, see page 16.

Out All Day

21

°

C

Heating ON

Summary of Contents for Q-Rad QRAD050E

































Reviews: