manualshive.com logo in svg

Dillenger KT-LCD3, User Manual, Page: 24 / 32

Share
Download
Dillenger KT-LCD3 User Manual Download Page 24

24

C5 settings are for controlling the maximum operating current. The default value is 10 
and value ranges from 0 to 10. Refer to table below for definition of each value.

C5 Value

Maximum Current Value (A)

00

Undefined

01

Undefined

02

Undefined

03

Maximum Current Value ÷ 2.00

04

Maximum Current Value ÷ 1.50

05

Maximum Current Value ÷ 1.33

06

Maximum Current Value ÷ 1.25

07

Maximum Current Value ÷ 1.20

08

Maximum Current Value ÷ 1.15

09

Maximum Current Value ÷ 1.10

10

Maximum Current Value

C6 Handlebar Function Setting

The C6 parameter setting will display on the meter after C5 settings. The KT-LCD3 will 
display as follows:

C6 Display

C6 settings are for the meter's backlight brightness. The default value is 3 and the 
setting range is 1-5. 

C6 Value

Backlight Brightness

1

Dimmest

2

Darker

3

Standard

4

Brighter

5

Brightest

C7 Value

Cruise Function

0

Disabled

1

Enabled

C8 Value

Motor Operating Temperature Function

0

Disabled

1

Enabled

Summary of Contents for KT-LCD3

































Reviews:

No comments