Dillenger KT-LCD3 User Manual Download Page 12 | Manualshive

Page: 12 / 32

Dillenger KT-LCD3 User Manual Download Page 12

12

Display of Power-Assist

: When motor is operating under power-assistance, the display

interface flashes the “ASSIST” sign. The indicator will cease after 5 seconds.

Battery Capacity Indicator

The KT-LCD3 can identify 24V, 36V, 48V battery capacities when used with supporting

controllers. When the battery capacity is over 70%, four bars from the battery indicator
will be displayed. As the battery capacities drop, the bars will change accordingly. Once
the power capacity is less than 15%, the battery indicator will be empty and show
zero bars. If the power display frame flashes, it is due to voltage shortage where the
controller will power off.

PAS Ratio

Press button or button to adjust the power assist ratio, changing the motor

output power. Range of power assist is between 1 and 5 (this can also be configured
according to the rider’s requirements), where one provides the lowest power and five
provides the highest. When the PAS ratio is set to zero, the power assist function is off.

Display of Powered Motor

Display of Power-Assist

«
...
10
11
12
13
14
...
»

Summary of Contents for KT-LCD3

































Reviews:

No comments