background image

31 

 

 

As you approach your vehicle upon seeing a valid iKey™

 

~Vehicle doors will unlock 

~Parking lights will flash Twice 

~If connected the Siren / Horn will “Chirp” Twice 

~The LED in the Start Button will light 

 

When you enter the vehicle: 
 

If you do not step on the Brake Pedal the system will work as follows: 

 

~Push the button once and turn on the ACCESSORIES 

~Push the button once more and on IGNITION 1 & 2 & ACCESSORIES 

~Push the button again and switch all circuits OFF 

 

If you step on the Brake Pedal the system will work as follows: 

 
~Push and hold in the start button and the STARTER will crank. 

~The driver decides when to release the start button to stop starter cranking. 

~Doors will lock 30 seconds after vehicle starts and brake is released. 

 

To turn engine OFF  

~

Depress the Brake and Push and HOLD the Start button in for 2 Seconds

 

~Doors will automatically unlock when engine is turned off. 

*** For safety, Doors will not auto unlock if engine has been on under 3 Minutes

 

When you walk away from the vehicle:

  

~All vehicle doors will auto lock and security features will arm 

~Parking lights will flash Twice

 

~If connected the Siren / Horn will “Chirp” Twice

 

 

Summary of Contents for 2GO KEYLESS iKEY RS





































Reviews: