background image

3

Hardware Specifications

„

Features

• This HDD unit has a finite usage lifetime. Therefore, be sure to back up all HDD data 

periodically and/or prepare a backup HDD unit.

• The HDD unit's lifetime will vary, depending on the usage conditions and environment. 

The above value is calculated assuming an ambient temperature of 20°C and 333 
hours of operation per month. (HDD access frequency of 20% or less)

• To use the hard disk longer by steady operation, read the attached “Instructions for 

Using the Hard Disk” carefully.

„

Environment

• Using the HDD unit in an environment that is excessively hot and/or humid will 

shorten the disk’s usage lifetime. A wet bulb temperature of 29°C or less is recom-
mended. This is equivalent to the following data.

Capacity

40GB

Average Seek Time 12msec (TYP)

Power Consumption

At Startup : 5.0W (TYP)
Read/Write : 1.8/1.8W (TYP)
During Wait : 0.2W (TYP)

Interface

PATA

Operation Lifetime

5 years, or 20,000 operating hours,whichever comes first

Weight

 Approx. 200g

Operating Tem-
perature

PS-3450A

 

PS3000-BA

5

°

C to 50

°

C

PS-3451A

5

°

C to 45

°

C

Storage Temperature

-20

°

C to +60

°

C

Ambient Humidity

10%RH to 90%RH (no condensation)
(Wet bulb temperature: 29°C or less)

Noise Resistance
(via Noise Simulator)

Noise Voltage: 1500Vp-p
Pulse Width: 50ns, 500ns, 1µs

Electrostatic Discharge

6kV

Vibration Resistance

4.9m/s

2

 (10Hz to 25Hz) (When Operating)

Shock Resistance

3920m/s

(1ms, Half-sine shock pulse) (When Shipping)

Temperature

at 35°C

at 40°C

Humidity

no higher than 64%RH

no higher than 44%RH

Summary of Contents for PS345XA-HD40









Reviews: