Digi XBee 865 Getting Started Manual Download Page 2

Page: 2 / 19

Digi XBee 865/868 LP Development Kit Getting Started Kit

(Part number 90002127 B)

Disclaimers

Information in this document is subject to change without notice and does not represent a commitment on

the part of Digi International. Digi provides this document “as is,” without warranty of any kind, expressed

or implied, including, but not limited to, the implied warranties of fitness or merchantability for a particular

purpose. Digi may make improvements and/or changes in this manual or in the product(s) and/or the

program(s) described in this manual at any time.

Trademarks and copyright

Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and

other countries worldwide. All other trademarks mentioned in this document are the property of their

respective owners.
© 2014 Digi International. All rights reserved.

Customer support

If you need assistance, contact technical support:
Telephone (8:00 am - 5:00 pm—U.S. Mountain Time):

866.765.9885 toll-free U.S.A. & Canada
801.765.9885 Worldwide

Fax: 952.912.4952
Online:

www.digi.com/support

Email:

[email protected]

Mail:

Digi International
11001 Bren Road East
Minnetonka, MN 55343
USA

Summary of Contents for XBee 865




















Search results

Summary of Contents for XBee 865

Reviews:

Related manuals for XBee 865

Brands by name

Popular brands

Digi XBee 865, Getting Started Manual

Search results

Summary of Contents for XBee 865

Reviews:

Related manuals for XBee 865

Brands by name

Popular brands