background image

Part of the mission statement of Digger Specialties, Inc. is Superior Products. The Turning Point

TM

  

Gate Opener is no exception. We are committed to providing the industry’s most innovative,  

reliable and aesthetically pleasing gate opening system. The system is hidden and quiet.  

By using the finest components, we strive to make the Turning Point

TM

 

Gate Opener  

second to none in performance, versatility, safety, and aesthetics.

LIMITED WARRANTY

     

The Turning Point

TM

 

Automatic Gate Opening Systems are warranted against defects for a period of (1) one year 

from the date of purchase, providing recommended installation procedures are followed. This warranty is in lieu of all 
other warranties expressed or implied (some states do not allow limitations on how long an implied warranty lasts, 
so this limitation may not apply to you) and shall be considered void if damage was due to improper installation or 
use, connection to improper power source, or if damage was caused by fire, flood, lightning or other act of God.  The 
manufacturer will not be responsible for any labor charges incurred in the removal or replacement of defective parts.

     In case of failure due to defective material or workmanship during the warranty period, the defective part will 
be repaired or replaced at the manufacturer’s option at no charge if returned freight prepaid. New or factory rebuilt 
replacements may be used. Replacement parts are warranted for the remaining portion of the original warranty period.  
The manufacturer will pay standard ground freight on the return of repaired or replaced items in warranty.

THE WARRANTY STATEMENTS CONTAINED IN THIS LIMITED WARRANTY EXTENDED BY DIGGER SPECIALTIES, INC. FOR ITS TURNING POINT

TM

 GATE 

OPENERS, AND THE PROVISIONS OF THIS WARRANTY SHALL CONSTITUTE THE ENTIRE LIABILITY OF DIGGER SPECIALTIES, INC. AND THE PROPERTY 
OWNER’S EXCLUSIVE REMEDY FOR BREACH OF THIS WARRANTY.  NO OTHER WARRANTY, WRITTEN, MADE BY DIGGER SPECIALTIES, INC. OR ANY 
AGENT THEREOF, WHICH IS NOT CONTAINED OR AUTHORIZED HEREIN, WILL BE RECOGNIZED BY DIGGER SPECIALTIES, INC.

TM

TM

TM

TM

TM

TM

IMPORTANT!

Please fill out both sides of the postcard on the next page  

and mail within 10 days to register your warranty.

Summary of Contents for Turning Point





















Reviews: