Diehl Program Timers Operating Manual Download Page 20

Page: 20 / 20

Operating Manual Program Timers Variotime Single and Variotime Twin

Diehl AKO Stiftung & Co.KG, Appliance Europe, Pfannerstraße 75-83, DE – 88239 Wangen

Tel. +49 (7522) 73-0 • Fax +49 (7522) 73-250 •

[email protected]

• www.diehl.com/controls/appliance

Subject to change without notice – issued 04-2015 – page 20/20

Additional data for Variotime
with panel-mount housing
only

Purposes/construction

Time control, electronic, incorporated

Mounting

Fitting into a panel opening

Mode of action

Type 1.B.S

Degree of contamination

Rated impulse voltage

2500 V (Input 110-120 V ac)
800 V (Input 24 V or 12 V)
4000 V (Output 250 V ac)

Connections

Mains and power relays

Tab terminals 6.3 x 0.8 mm in compliance with EN 61210

Approvals

VDE – ENEC and UL/CSA (technical conditions apply)

Summary of Contents for Program Timers





















Search results

Summary of Contents for Program Timers

Reviews:

Related manuals for Program Timers

Brands by name

Popular brands

Diehl Program Timers, Operating Manual

Search results

Summary of Contents for Program Timers

Reviews:

Related manuals for Program Timers

Brands by name

Popular brands