manualshive.com logo in svg

Diamond HR301-16, User Manual

Share
Download
Diamond HR301-16 User Manual Download Page 133

User Manual of Digital Video Recorder 

 

132 

9.1

 

Configuring General Settings 

Purpose: 

Network settings must be properly configured before you operate device over network. 

Steps: 

1.

 

Enter the Network Settings interface. 

Menu > Configuration > Network 

 

HRA03

 

 

HR301 

Figure 9. 1

 

Network Settings Interface 

 

Note: 

HR301-4 only supports 10M/100Mbps NIC type. 

2.

 

Select 

 

tab. 

3.

 

In the 

General Settings 

interface: you can configure the following settings: NIC Type, IPv4 Address, 

IPv4 Subnet Mask, IPv4 Gateway, MTU and DNS Server. 

If the DHCP server is available, you can check the checkbox of 

DHCP

 to automatically obtain an IP 

address and other network settings from that server. 

  Note:

 

The valid value range of MTU is 500 ~ 9676.   

Summary of Contents for HR301-16

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands