background image

1 7

III.

GENERAL INSTRUCTIONS

Carefully read the instruction handbook before using the appliance.

• After installation keep the instruction handbook for future consultation.

FIRE HAZARD - Keep the area around the appliance clear and free from combustible materials. Do not

keep flammable materials in the vicinity of the appliance.

Install the appliance in a well-ventilated place to avoid the creation of dangerous mixtures of unburnt

gases in the room.

Air recirculation must take in account the air necessary for combustion, 2 m³/h/kW gas power, and

also the “well-being” of those working in the kitchen.

Inadequate ventilation causes asphyxia. Do not obstruct the ventilation system of the place where the
appliance is installed. Do not obstruct the vents or ducts of this or other appliances.

• Place emergency telephone numbers in a visible position.

Installation, maintenance and conversion to another type of gas must only be carried out by qualified personnel authorised by
the manufacturer. For assistance, contact an authorised technical centre. Demand original spare parts.

This equipment is designed for cooking food. It is intended for industrial use. Any other use is to be considered 

improper

.

This appliance is not intended for use by people (including children) with limited physical, sensory or mental abilities or without
experience and knowledge of it, unless they are supervised or instructed in its use by a person responsible for their safety.

The appliance must be used by 

trained personnel

. Do not leave the appliance unattended when operating.

• Turn the appliance off in case of fault or poor operation.

• Do not use products (even if diluted) containing chlorine (sodium hypochlorite, hydrochloric or muriatic
acid, etc.) to clean the appliance or the floor under it. Do not use metal tools to clean steel parts (wire
brushes or  Scotch Brite type scouring pads).

• Do not allow oil or grease to come into contact with plastic parts.

• Do not allow dirt, fat, food or other residuals to form deposits on the appliance.

Do not clean the appliance with direct jets of water.

The symbol 

L

 given on the product indicates that it should 

not

 be considered domestic waste, but must be

correctly disposed of in order to prevent any negative consequences for the environment and the health of persons.
For further information regarding the recycling of this product, contact the product agent or local dealer, the
after-sales service or the local body responsible for waste disposal.

Warnings:

Do not store or use gasoline or other flammable vapours, liquids or items in the vicinity of this or any other appliance.

Do not spray aerosols in the vicinity of this appliance while it is in operation.

Never check for leaks with an open flame

The appliance is not suitable for a marine environment.

.

Failure to observe the above can compromise the safety of the appliance. Failure to
observe the above invalidates the warranty.

sos

Summary of Contents for E17/4ID8T












Reviews: