background image

28

To modify a parameter: 

- Press

-  Press       

or             within 15 s 

-  Press         

or leave for 15 s. 

To exit the procedure: 

-  Press        

and             for 4 s, or leave for 60 s. 

Interrupt the device power supply after modify the parameters. 

 RESETTING CONFIGURATION PARAMETER DEFAULT VALUES

- Ensure the device is in “stand-by” mode and no procedures are running. 

- Press       

and             for 4 s: the display will show “PA” 

- Press

- Press     

or            within 15 s to set “743” 

- Press          

or leave for 15 s 

-  Press       

and              per 4 s: the display will show “dEF” 

- Press

- Press        

or            within 15 s to set “149” 

- Press        

or leave for 15 s: the display will flash “dEF” for 4 s, after which the device will exit the 

procedure 
- Interrupt the power to the device. 
Ensure that the parameter default values are appropriate. 

2.18 

USAGE PRECAUTIONS 

x

Do not hang off the doors, the machine's stability is guaranteed with the doors open. 

x

DO NOT USE sharp objects in the surroundings of the coolant circuit either in EVAPORATORS, 
CONDENSERS, FAN PROTECTIONS, input and output lines. 

x

Working with wet hands or bare foot when handing the control and surroundings of electrical parts or 
components is not recommended. 

 
 

3

 MAINTENANCE  

With these guidelines, we would like to offer both you and the technical assistance service help so that the 
cooler always works perfectly throughout its useful life. 
We will deal with the cleaning you can carry out as well as a quick machine check before contacting the 
technical support service. We hope this will be useful. 

3.0

USER CLEANING 

Before carrying out any cleaning operations, the appliance must be 

disconnected from the socket,

 and the 

power switch turned to 

OFF

 (if your model has it). 

Some models are equipped with a drainage pipe for cleaning, as well as for collecting the possible flow of 
liquids from the food. It is essential to remove and clean the drainage pipe plug during the cleaning 
operation, to prevent it from being blocked up with solid waste. This is so that any liquids present do not 
become stagnant. 

It should be installed again after cleaning.

 

It is essential to disconnect the appliance if you are going to clean with water. Panels should not be moved 
to access electrical components except by technical staff authorised to carry out maintenance and repair 
operations

Summary of Contents for 18G300500000


















Reviews: