manualshive.com logo in svg

Dialogic DSI SPCI Network Interface Boards, Programmer'S Manual, Page: 80 / 111

Share
Download
Dialogic DSI SPCI Network Interface Boards Programmer'S Manual Download Page 80

6 Message Reference 

80 

Parameter Description: 

Board Status 

Value 

Mnemonic 

Description 

0x60 

SSDSI_RESET 

Processor successfully reset. 

0x62 

SSDSI_FAILURE 

Failure to reset board. 

0x64 

SSDSI_BRD_RMVD 

Board removed (hot swap only). 

0x65 

SSDSI_BRD_INS 

Board inserted (hot swap only). 

0x66 

SSDSI_LIC_FAIL 

License validation failure. 

0x67 SSDSI_LIC_CRP 

License 

corruption. 

0x70 

SSDSI_BCONG_CLR 

Message congestion towards board cleared. 

0x71 

SSDSI_BCONG_ON 

Message congestion towards board occurred. 

0x72 

SSDSI_DIS_CLR 

Message congestion discard towards board cleared. 

0x73 

SSDSI_DIS_ON 

Message congestion discard towards board. 

0x74 

SSDSI_FAIL 

Message congestion - board failure. 

6.4.2

 

s7_mgt Completion Status Indication 

Synopsis: 

Message issued by s7_mgt on completion of initial configuration sequence. 

Message Format: 

MESSAGE HEADER 

Field Name 

Meaning 

type API_MSG_CNF_IND

 (0x0f09) 

id 

0 

src 0xcf 

dst Notification 

Module

 (see below) 

rsp_req 

0 

hclass 

0 

status Completion 

Status

 (see below) 

err_info 

Reserved for future use 

len 

0 

Summary of Contents for DSI SPCI Network Interface Boards
















































































































Reviews:

No comments