www.dfi.com
9
Chapter 2 Hardware Installation
Chapter 2
Chapter 2 - Hardware Installation
Board Layout
31
Intel
C236/Q170
KD632-C236: C236
KD632-Q170: Q170
1
LPC
1
13
2
14
1
13
12
24
Standby
Power
LED
1 2
11
1
2
7
8
1
USB 2.0
2
10
2
10
9
2
10
6
5
2
1
USB 3.1
Gen1
1
19
11
1
SATA0(R2)
1
SATA4(R1)
SATA 3.0
1
1
SATA1(R3)
SATA 3.0
1
SPI
Flash
BIOS
5
1
2
SMBus
IT8893E
Clear CMOS
(JP9)
JP29
JP30
1
JP27
1
JP33
1
JP28
1
Buzzer
PCI 2
PCI 1
1
2
5
1
2
5
6
1
2
5
6
(JP1)
(JP3)
(JP2)
(JP3)
(JP2)
(JP1)
COM 2
RS232/422/485
Select
Nuvoton
NCT6116D
Battery
Battery
PCIe 4 (PCIe x4)
PCIe 3 (PCIe x4)
Chassis
Intrusion
1
S/PDIF
1
Realtek
ALC888S
PCIe 1 (PCIe x16)
Digital
I/O
19
2
1
DDR4_1
DDR4_2
DDR4_3
DDR4_4
CPU Fan
1
Socket LGA1151
PTN3355
6
2
6
5
1
COM 1
RS232/422/485
Select (JP5)
JP6
+12V
Power
4
8
1
5
2
COM 1 RS232/Power
Select (JP8)
COM 1 RS232/422/485
Select (JP7)
2
9
10
1
Front Audio
19
System
Fan 3
System
Fan 1
1
Front
Panel
10
USB 5-6
SATA 3.0
ATX
Power
System
Fan 2
LAN LED
2
10
9
1
4
Vertical
USB 9
USB
7-8
1
1
USB
13-14
Mini PCIe
1
2
9
Intel I211AT
Intel I219LM
COM 6
5
1
6
2
6
5
1
2
5
1
M.2 M Key
1
2
9
1
2
9
1
2
9
1
2
9
PCIe 2 (PCIe x16)
PCIe 5 (PCIe x4)
COM 2
RS232/Power
Select (JP4)
6
TPM 1.2/2.0
(opt.)
LAN 2
USB 2
USB 1
USB 3.1 Gen1
PS/2 KB/MS
USB 6
USB 5
USB 2.0
DVI-I (DVI-D signal)
DP++
1
Line-in(opt.)
Line-out
Mic-in
1
Mini PCIe/mSATA/SATA4(R1)
Signal Select (JP34, JP15)
COM 5
(JP34)
(JP15)
1
M.2_SATA, SATA3(R5)/M.2_PCIe/SATA2(R4), SATA3(R5)
Signal Select (JP23)
1
1
LAN 1
USB 4
USB 3
USB 3.1 Gen1
COM 1
VGA
COM 4
COM 3
COM 2
-
JP32
SATA3(R5)
SATA2(R4)
System Memory
Standby
Power LED
Features
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lit red, it indicates that there is power on the system
board. Power-off the PC then unplug the power cord prior to installing any devices.
Failure to do so will cause severe damage to the motherboard and components.
DDR4_2
DDR4_1
DDR4_4
DDR4_3
•
Four 288-pin ECC/Non-ECC U-DIMM up to 64GB (KD632-C236)
Four 288-pin Non-ECC U-DIMM up to 64GB (KD632-Q170)
•
Dual Channel DDR4 2133/2400 MHz
