Water Seals
Replacement
Step 1:
Remove cylinder from washer (see Cylinder (basket)
removal).
Step 2:
Remove water seals from the seal mounting plate on
the cylinder shaft. These are removed with your fingers.
Step 3:
The primary and secondary seals that mount on the
sealing ring may be slid over the shaft and seated on
the metal sealing ring with your fingers. In the unlikely
event that the metal ring that mounts these sealing
rings were to be damaged or moved, a new one would
need to be pressed on. The seal mounting ring must be
pushed against the stop on the shaft. After installing
the seals, lubricate the faces of the seals with silicone
grease.
Step 4:
Install cylinder (see Cylinder (basket) reassembly).
Guard Ring & Mating Ring
Seals
Mating Ring & Mounting Ring
Outer Tub
Removal
Step 1:
The outer tub can easily be removed when the tub front,
cylinder and bearing housing has been removed as
outlined previously.
Step 2:
At that point the only attachments to the chassis are the
two front strap mounting bolts.
Reassembly of the Cylinder
Step 1:
Use the hub of the drive pulley, a stack of 5/8” flat washers and a 3” long 5/8” bolt to pull the
cylinder shaft through the bearings. After the 3” bolt a 2” long bolt will be required to finish pulling
the cylinder shaft through.
Step 2:
Remove the 1/2” bolt and nut from the top of the outer tub clamping band.
Step 3:
Install Dexter Tool part # 8545-056-001 on the back of the outer tub to adjust tub front to cylinder
clearance.Thread 5/8” bolt through tool and into cylinder shaft. Push the outer tub forward 1/4” to
1/2” with tool 8545-056-001by tightening the 5/8” bolt. This will ease the installation of the outer tub
front.
Step 4:
Clean the silicone rubber off the tub front and the outer tub.
Step 5:
Install new bead of silicone rubber on tub front.
Step 6:
Install tub front.
Step 6A:
Align hole in top of tub front with notch in top of outer tub.
Step 6B:
Use 4-6 #11R vise grip clamps to hold tub front to outer tub. A rubber mallet may be needed to
properly seat the tub front into the outer tub.
Step 6C:
Install tub front gasket around outer edge of tub front and outer tub flange. The opening should be
centered at the top.
Step 6D:
Remove vise grips. The tub front gasket will hold the tub front in place.
Step 7:
Install tub front clamp ring and tighten. Tap around the clamp ring with a rubber mallet to seat the
ring and gasket while tightening the clamp ring bolt.
Step 8:
Adjust clearance between the outer tub front and the front lip of the cylinder to 5/16”.
Step 9:
Tighten the outer tub clamping band.
Step 10:
If necessary, the outer tub may be adjusted up or down and side to side with the 2 bolts that fasten
the bottom of the outer tub clamping band to the frame.
Step 11:
Remove Dexter Tool part 8545-056-001 from the back of the outer tub.
Step 12:
Install drive pulley.
Step 12A:
Install hub on cylinder shaft.
Step 12B:
Hold hub against rear bearing with 5/8” bolt and flat washer in end of cylinder shaft.
Step 12C:
Line up 3 unthreaded holes in pulley with the 3 threaded holes in hub.
Step 12D:
Insert 3 pulley bolts and tighten evenly alternating bolts to 30ft/lbs.
NOTE:
Overtightening or uneven tightening can break drive pulley.
Step 13:
Install drive belts & back panel.
Step 14:
Install door lock. All mounting holes should be sealed with silicone rubber.
Step 15:
Install door, masking ring, front panel, lower service panel and top.
62
63
Part # 8533-075-001 6/22
Part # 8533-075-001 6/22
Machine
Mounting
Installation
& Operation
Programming
Trouble-
shooting
Machine
Service
Electrical
Wiring
Parts
Data
50Hz
Parts
Maintenance
Service Elec.
Compnents
