Dexter Laundry T-1450 Parts And Service Manual Download Page 22

Page: 22 / 71

Part # 8533-075-001 6/22

Section 4:

Trouble Shooting

Common Troubleshooting Solutions

Symptom Probable Cause Suggested Remedy

Machine

does not

start

Power Supply

Check these areas: Circuit breakers, Voltage, Power leads,

Power connections. Is front display LED showing a dollar

amount.

Door Switch

Check for continuity through door switch when door is

closed. If no continuity, adjust or replace door switch.

Control Breaker or

Fuse

Check 1.5 amp (T-1200. uses 2.5amp) breaker or fuse for

continuity. If no continuity, replace breaker or fuse.

Control Trans-

former

Check voltage output from control transformer for 120VAC.

If voltage is incorrect, replace transformer.

Check PCB board

Check all wire connections for sure contacts.

Check wiring be-

tween PCB

Check data cable phone type connectors unplug and VFD

and replug with power removed.

Check Relay PCB

Check all wire connections for sure contact.

Check Door Sole-

noid

Check that 120 v power is at solenoid after start button is

pushed.

Door does

not lock

Check display for

fault code

Does F1 show on the front of display. If yes follow tests

described in fault code section.

Door locking sole-

noid

Check to insure that solenoid is receiving 120VAC from main

relay PCB. If it is, replace solenoid.

Door Switch

Check for continuity through door latch switch when door

closed. If no continuity, adjust or replace door switch.

Door will

not open

Thermoactuator

Check to see if thermoactuator(s) and/or its mechanism is

stuck or binding and not allowing the door lock solenoid to

open. Check to be sure that the locking thermoactuator is

not receiving 120VAC during the last 1 1/2 minutes of the

cycle. Also check to see that the unlocking thermoactuator

is receiving 120VAC during the last minute of the cycle. If

the thermoactuators do not receive voltage at the correct

times, change the timer. If the timing and voltage are cor-

rect, replace the thermoactuator.

Door will not

open

Door Rod

Check to see that door rod from solenoid to lock ass’y is long

enough to allow lock ass’y to disengage. If not, adjust rod.

Door Lock Solenoid

Check that door lock solenoid is not stuck closed. If stuck, replace

solenoid.

No hot water

in detergent

dispenser

Water Valve Coil

Check coil continuity at terminals and replace if no continuity. 120

V power only on for 20 second in wash bath.

Water Inlet

Check water inlet screens for blockage and clean screens if neces-

sary.

Water

Check to insure that water is turned on and operating.

P-20 Wire Harness

Check black & white harness.

Machine

Mounting

Installation

& Operation

Programming

Trouble-

shooting

Machine

Service

Electrical

Wiring

Parts

Data

50Hz

Parts

Maintenance

Service Elec.

Compnents

Summary of Contents for T-1450








































































Search results

Summary of Contents for T-1450

Reviews:

Related manuals for T-1450

Brands by name

Popular brands

Dexter Laundry T-1450, Parts And Service Manual

Search results

Summary of Contents for T-1450

Reviews:

Related manuals for T-1450

Brands by name

Popular brands