ENGLISH
9
Mounting Guards (fig. 2)
WARNING: To reduce the risk of serious
personal injury, turn tool off and
disconnect tool from power source before
making any adjustments or removing/
installing attachments or accessories.
Before reconnecting the tool, depress and
release the trigger switch to ensure that the tool
is off.
CAUTION:
Guards must be used with
this grinder.
When using the DWE8200S or the DWE8200T or
the DWE8210S or DWE8200P or DWE8210P
grinder for cutting metal or masonry a Type 1 guard
must be used.Type 1 guards are available at extra
cost from
D
E
WALT
distributors.
NOTE:
Please refer to the
Grinding and Cutting
Accessory Chart
at the end of this section to
see other accessories that can be used with these
grinders.
MOUNTING CLOSED (TYPE 1) OR STANDARD (TYPE 27)
GUARD
CAUTION:
Turn off and unplug the
tool before making anyadjustments
or removing or installing attachments
or acces-sories. Before reconnecting
the tool, turn the switch on and off to
ensure that the tool is off.
Hubbed wheels install directly on the M10
(DWE8200T, DWE8200S, DWE8200P), M14
(DWE8210S, DWE8210P) spindle. Thread of
must
match thread of spindle.
accessory
1. Loosen screw, until the guard lug (k) can rotate
freely in the groove (j) on the gear case hub.
2. Rotate guard (f) into desired working position.
The guard body should be positioned between
the spindle and the operator toprovide
maximum operator protection.
3. Tighten the screw to secure the guard on the
gear case cover. (Fasten torque no less than
2.5 N-M). You should be unable to rotate the
guard by hand. Do not operate grinder with a
loose guard.
4. To remove the guard, loosen screw and pull up
on the guard.
CAUTION:
Failure to properly seat
the wheel before turning the tool on
may result in damage to the tool or the
wheel.
F
Removing a Grinding or
Cutting Disc (fig. 1, 4, 5)
WARNING:
Do not use a damaged
disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange (d) correctly onto the
spindle (b) (fig. 4).
3. Place the disc (n) on the backing flange (d).
When fitting a disc with a raised centre, make
sure that the raised centre (l) is facing the
backing flange (d).
4. Screw the threaded clamp nut (e) onto the
spindle (b) (fig. 5):
a. The ring on the threaded clamp nut (e) must
face towards the disc when fitting a grinding
disc (fig. 5A);
b. The ring on the threaded clamp nut (e) must
face away from the disc when fitting a cutting
disc (fig. 5B).
5. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
6. Tighten the threaded clamp nut (e) with the
wrench or the hex key provided
7. Release the spindle lock.
8. To remove the disc, loosen the threaded clamp
nut (e) with the wrench or the hex key provided.
NOTE:
Edge grinding and cutting can be performed
with Type 27 wheels designed and specified for
this purpose; 6 mm thick wheels are designed for
surface grinding while 3 mm wheels are designed
for edge grinding. Cutting can also be performed by
using a Type 1 wheel and a Type 1 guard.
The recommended diameter of grinding or cutting
disc for the tool is 100mm(DWE8200S, DWE8200T,
DWE8200P) or 125mm(DWE8210S, DWE8210P) .
itting and
Mounting Wire Brushes
Wire cup brushes or wire wheels screw directly
on the grinder spindle without the use of flanges.
Use only wire brushes or wheels provided with
a
M10 (DWE8 00S & DWE8 00T
)
(DWE8 10S, DWE8210P)
required when using wire
CAUTION: Wear work gloves when
handling wire brushes and wheels.
They can become sharp.
brushes and wheels.
