41
english
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING:
No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power input
of this tool (see
Technical Data
).The minimum
conductor size is 1.5 mm
2
; the maximum length
is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Attaching Side Handle (fig. 1)
WARNING:
Before using the tool, check
that the handle is tightened securely.
Screw the side handle (C) tightly into one of the
holes on either side of the gear case. The side
handle should always be used to maintain control of
the tool at all times.
Accessories and Attachments
It is important to choose the correct guards,
backing pads and flanges to use with grinder
accessories. Refer to chart at the end of this section
for information on choosing the correct accessories.
NOTE:
Edge grinding can be performed with
Type 27 wheels designed and specified for this
purpose.
WARNING:
Accessories must be rated
for at least the speed recom mended
on the tool warning label. Wheels and
other accessories running over rated
INTENDED USE
The DWE4056, DWE4057, DWE4120, DWE4156,
DWE4157 heavy-duty angle grinders have been
designed for professional grinding, sanding, wire
brushing and cutting applications.
DO NOT
use grinding wheels other than centre
depressed wheels and flap discs.
DO NOT
use under wet conditions or in the
presence of flammable liquids or gases.
These heavy-duty angle grinders are professional
power tools.
DO NOT
let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Soft Start Feature
(DWE4056, DWE4057, DWE4156, DWE4157)
The soft start feature allows a slow speed build-up
to avoid an initial jerk when starting. This feature is
particularly useful when working in confined spaces.
No-Volt
(DWE4056, DWE4057, DWE4156, DWE4157)
The No-volt function stops the grinder restarting
without the switch being cycled if there is a break in
the power supply.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your
D
e
WALT
tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
WARNING:
115 V units have
to be operated via a fail-safe
isolating transformer with an earth
screen between the primary and
secondary winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
e
WALT
service organisation.
Summary of Contents for DWE4056
