ENGLISH
6
c)
Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
d)
The rated speed of the accessory must be at
least equal to the maximum speed marked
on the power tool.
Accessories running faster
than their rated speed can break and fly apart.
e)
The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool.
Incorrectly sized
accessories cannon be adequately guarded or
controlled.
f)
The arbour size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool.
Accessories
with arbour holes that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.
g)
Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheel for chips and cracks, backing
pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute.
Damaged accessories will
normally break apart during this test time.
h)
Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments.
The eye protection must
be capable of stopping flying debris generated
by various operations. The dust mask or
respirator must be capable of filtrating particles
generated by your operation. Prolonged
exposure to high intensity noise may cause
hearing loss.
i)
Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.
j)
Hold power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord.
Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
shock the operator.
k)
Position the cord clear of the spinning
accessory.
If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.
l)
Never lay the power tool down until the
accessory has come to a complete stop.
The
spinning accessory may grab the surface and
pull the power tool out of your control.
m)
Do not run the power tool while carrying it at
your side.
Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
n)
Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
o)
Do not operate the power tool near
flammable materials.
Sparks could ignite these
materials.
p)
Do not use accessories that require liquid
coolants.
Using water or other liquid coolants
may result in electrocution or shock.
FURTHER SAFETY INSTRUCTIONS
FOR ALL OPERATIONS
Causes and Operator Prevention
of Kickback
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation at
the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these
conditions.
Summary of Contents for D28492
