background image

English

8

•  If the grass is repeatedly mowed in the same direction, it will be “trained” so that 

the striped appearance is more pronounced and longer lasting. Grooving of the 
turf from the tires will occur.

•  For emptying material collection systems or for any other operation involving the 

mower deck, before leaving the operator station:

•  Disengage the mower blades.
•  Squeeze the steering controls and latch the neutral locks.
•  Place the gear shift lever in neutral.
•  Shut off the engine.
•  Apply wheel chocks and/or engage the parking brake.

Transporting Mower

•  If ramps are used, be sure they are secured to the trailer, truck bed, etc. and are 

designed for the application.

•  The mower should be pushed or pulled onto or off the trailer, truck bed, etc., never try 

to drive it on.

•  Engage the parking brake, secure mower with chocks, straps, etc.
•  Make sure accessories and attachments are secured or removed.

PRODUCT CARE

Maintenance Schedule

 

WARNING: Before performing any maintenance or repairs, disengage the 

PTO, engage the parking brake, stop the engine, and remove the key to 

prevent unintended starting.

Follow the maintenance schedule given below. This chart describes service guidelines only.

Mowing

The following information will be helpful when operating your mower.

 

WARNING: Plan your mowing pattern to avoid discharge of materials 

toward roads, sidewalks, bystanders, and the like. Also, avoid discharging 

material against a wall or obstruction which may cause discharged material 

to ricochet back toward the operator.

•  Be sure area is clear of rocks, sticks, toys, wire or other objects that could be thrown by 

the mower. Survey the entire area to be mowed. Make sure that the accessories and 
attachments would be suitable for use on the terrain.

•  Use care when approaching blind corners, shrubs, trees or other objects that could 

obstruct vision.

•  To mow grass and produce a striped pattern:

•  Pick a point on the opposite side of the area to be mowed (post, tree, shrub, etc).
•  If on a hillside, start at the bottom so that the turns are uphill rather 

than downhill.

•  Align the mower so as to head directly toward the object on the far side.
•  Slowly increase the speed of the machine to match cutting conditions, terrain 

and operator familiarity with the controls and keep the machine headed directly 
toward the alignment object. Do not go fast as to reduce cut quality or to be 
uncomfortable in controlling the speed and direction of the machine.

•  When approaching the other end of a strip, slow down or stop before turning. A 

U-turn is recommended.

•  To prevent rutting or grooving of the turf, change the direction that the strips 

are mowed by approximately 45° the next and each subsequent time that the 
area is mowed.

CONTROLS & OPERATION, cont'd

Before Each 

use

1st Five  

hours

Every  

40 hours

Every  

100 hours

Every  

300 hours

Prior to 

storing

Check/Clean Engine intake screens & Cooling Fans *

P

P

Check/Clean Exhaust Manifold, Muffler Pipe & Muffler shields *

P

P

Check/Clean Top & Underside of Deck, Under & Around spindle Covers & Belt Area *

P

P

Check/Clean Around Fuses, Wiring & Wiring harnesses *

P

P

Check/Clean Around Transmission, Axle & Fans *

P

P

Clean Mower

P

P

Check Fuel level

P

Check Belts & Controls

P

Check Engine Oil level

P

Check loose or Missing Parts

P

Clean or Replace Air Filter Element

P

P

lube Deck idler Pulley Pivot Arms

P

Change Engine Oil & Filter

P

P

sharpen & Balance Blades

P

lube Brake lever Points

P

lube Control Bellcrank Pivot

P

lube Transmission-Jackshaft Couplers

P

lube Ball Joint

P

Check spark Plug Condition & gap

P

P

Change hydraulic Oil & Filter  †

P

* — Perform more frequently under dusty conditions.

† — Change the hydraulic oil and filter after the first 50-100 hours.

Summary of Contents for 55AI6HN





































Reviews: