Develco ZHOT101 Technical Manual Download Page 17

Page: 17 / 20

ZigBee Home Automation Commissioning

ZigBee Home Automation specifies a common language which all ZigBee Home Automation devices

must use to document commissioning of the device.

Below is a table outlining the Develco ZigBee HA device MMI using this common language.

ZigBee Action

Availability

What To Do To Device To Perform Action

Join Network

Routers and End Devices

Press and hold button until Reset To Factory

Fresh Settings menu is reached (continuous

flash of LED) and then release button.

Form Network

Not Supported

Allow Others To Join

Network

Not Supported

Restore Factory Fresh

Settings

All devices

Press and hold button until Reset To Factory

Fresh Settings menu is reached (continuous

flash of LED) and then release button.

Pair Devices

Routers and End Devices

Press and hold button until Pair Devices menu

is reached (LED flashes twice) and then

release button.

Enable/Disable Identify

Mode

All devices

Press and hold button until Enable Identify

Mode menu is reached (LED flashes once) and

then release button.

Create Scene

Not Supported

Summary of Contents for ZHOT101





















Search results

Summary of Contents for ZHOT101

Reviews:

Related manuals for ZHOT101

Brands by name

Popular brands

Develco ZHOT101, Technical Manual

Search results

Summary of Contents for ZHOT101

Reviews:

Related manuals for ZHOT101

Brands by name

Popular brands