background image

www.desatech.com

119426-01A

32

OPTIONAL POSITIONING 

OF THERMOSTAT 

SENSING bULb

(Thermostat-Controlled Models Only)

FOR MASONRY AND FACTORY-
BUILT METAL FIREPLACE

If your log set cycles to pilot, but the room tem

-

perature drops to a lower than ideal comfort level 

before the log set comes back on, you may want 

to reposition the thermostat sensing bulb.

The thermostat sensing bulb is located on the gas 

valve assembly. This location allows the ther

-

mostat to keep the room temperature at an ideal 

comfort level for most fireplace applications. For 

positioning the thermostat sensing bulb elsewhere, 

an adhesive-backed mounting clip is available 

(see Figure 42).

Tools needed: 5/16" hex driver or socket 

1.  Locate the gas valve assembly and thermostat 

sensing bulb (see Figure 43). 

2.  With 5/16” hex driver or socket, loosen the 

thermostat screw. Carefully slide the thermo

-

stat sensing bulb out of the retaining clamp 

(see Figure 44). 

 

Note:

 Do not remove the screw. Make sure 

you  tighten  the  screw  after  removing  the 

thermostat sensing bulb. 

 

IMPORTANT:

  Do  not  force  or  bend  the 

thermostat sensing bulb or capillary. 

Capillary 

Screw

Retaining Clamp 

Thermostat 
Sensing Bulb 

Figure 43 - Location of Gas Valve 

Assembly and Thermostat Sensing Bulb 

Thermostat 
Sensing Bulb 

Gas Valve 
Assembly 

Figure 42 - Adhesive-backed Mounting 

Clip 

Figure 44 - Removing Thermostat 

Sensing Bulb 

Figure 45 - Locating Thermostat Sensing 

Bulb on Masonry Fireplace 

Figure 46 - Locating Thermostat Sensing 

Bulb on Factory-built Metal Fireplace 

Adhesive-backed 
Mounting Clip 

Thermostat 
Sensing Bulb 

Figure 47 - Installing Thermostat Sensing 

Bulb Behind Glass Doors 

Adhesive-
backed 
Mounting Clip 

Glass Doors 

Thermostat 
Sensing Bulb 

Adhesive-backed 
Mounting Clip 

Thermostat 
Sensing Bulb 

(Unit Will 
Differ From 
Illustration)

(Unit Will 
Differ From 
Illustration)

3.  The thermostat sensing bulb may be located 

to the lower right front side of fireplace. De

-

termine location of sensing bulb, but do not 

mount sensing bulb until step 4. If you have a 

masonry fireplace, see Figure 45 for location. 

  If you have a factory-built metal fireplace, see 

Figure 46 for location. 

  If your fireplace has glass doors, position 

sensing bulb directly behind door gap on right 

bottom side (see Figure 47).

Summary of Contents for VUL 18R, VUL24R, VUL30R, HR B3930, HR 3924R, CRB3624T, VUL 18T, VUL24T, VUL30T, HR B3624T













































Reviews: