background image

www.desatech.com

121880-01B

10

INsTallaTIoN

Continued

Attaching Mounting Bracket To Wall

Note:  Wall  anchors,  mounting  screws  and 
spacers are in hardware package. The hard-
ware package is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs
1.  Drill holes at marked locations using 9/64" 

drill bit.

2.  Place  mounting  bracket  onto  wall.  Line 

up last hole on each end of bracket with 
holes drilled in wall.

3.  Insert mounting screws through bracket 

and into wall studs.

4.  Tighten screws until mounting bracket is 

firmly fastened to wall studs.

Attaching To Wall Anchor Method

For  attaching  mounting  bracket  to  hollow 
walls (wall areas between studs) or solid walls 
(concrete or masonry)
1.  Drill  holes  at  marked  locations  using 

5/16" drill bit. For solid walls (concrete or 
masonry), drill at least 1" deep.

2.  Fold wall anchor as shown in Figure 9.
3.  Insert wall anchor (wings first) into hole. 

Tap anchor flush to wall.

4.  For thin walls (1/2" or less), insert red key 

into  wall  anchor.  Push  red  key  to  “pop” 
open anchor wings (see Figure 10). 

IM-

PORTANT: 

Do not hammer key! For thick 

walls (over 1/2" thick) or solid walls, do not 
pop open wings.

5.  Place mounting bracket onto wall. Line up 

last hole on each end of bracket with wall 
anchors.

Figure 9 - Folding Anchor

Figure 11 - Mounting Heater Onto 

Mounting Bracket

Stand-
Out Tab

Figure 10 - Popping Open Anchor Wings 

For Thin Walls

Mounting Bracket (attached to wall)

Horizontal Slots

6.  Insert mounting screws through bracket 

and into wall anchors.

7.  Tighten screws until mounting bracket is 

firmly fastened to wall.

Placing Heater On Mounting Bracket

1.  Locate two horizontal slots on back panel 

of heater.

2.  Place heater onto mounting bracket. Slide 

horizontal  slots  onto  stand-out  tabs  on 
mounting bracket.

Installing Bottom Mounting Screws

1.  Locate two bottom mounting holes. These 

holes are near bottom on back panel of 
heater (see Figure 12).

2.  Mark screw locations on wall.
3.  Remove heater from mounting bracket.

Figure 12 - Installing Bottom Mounting 

Screws

Side View

Front View

Wall

Spacer

Heater

Summary of Contents for VP20BTB





















































Reviews: