background image

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-
lowed exactly, a fire or explosion may result causing 
property damage, personal injury or loss of life.

—  Do  not  store  or  use  gasoline  or  other  flammable 

vapors and liquids in the vicinity of this or any other 

appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do not use any 

phone in your building.

•  Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

—  Installation and service must be performed by a quali-

fied installer, service agency or the gas supplier.

INSTALLER:  Leave  this  manual  with  the  appliance. 
CONSUMER: Retain this manual for future reference.

WINCHESTER OAK UNVENTED (VENT-FREE)

GAS LOG HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

24" VARIAbLE MANUALLy-CONTROLLED MODELS

SGS3124P AND SGS3124N

Also design-certified as vented decorative appliances

Patent Pending

Summary of Contents for SGS3124N





























Reviews: