background image

www.desatech.com

107068-01K

 WARNING: This product con-

tains and/or generates chemicals 

known to the State of California 

to cause cancer or birth defects 

or other reproductive harm.

IMPORTANT: Read this owner’s 

manual carefully and completely 

before  trying  to  assemble,  op-

erate  or  service  this  fireplace. 

Improper  use  of  this  fireplace 

can  cause  serious  injury  or 

death  from  burns,  fire,  explo-

sion, electrical shock and carbon 

monoxide poisoning.

 DANGER: Carbon monoxide 

poisoning may lead to death!

Carbon Monoxide Poisoning:

 Early signs of carbon 

monoxide poisoning resemble the flu, with head

-

aches, dizziness or nausea. If you have these signs, 

the heater may not be working properly. 

Get fresh 

air at once!

 Have heater serviced. Some people 

are more affected by carbon monoxide than others. 

These include pregnant women, people with heart 

or lung disease or anemia, those under the influence 

of alcohol and those at high altitudes.

Natural  and  Propane/LP  Gas:

 Natural and pro

-

pane/LP  gases  are  odorless. An  odor-making 

agent is added to these gases. The odor helps you 

detect a gas leak. However, the odor added to the 

gas can fade. Gas may be present even though no 

odor exists.

Make certain you read and understand all warn

-

ings. Keep this manual for reference. It is your 

guide to safe and proper operation of this heater.

  WARNING:  Any  change  to 

this  heater  or  its  controls  can 

be dangerous.

  WARNING:  Do  not  use  a 

blower  insert,  heat  exchanger 

insert or other accessory not ap-

proved for use with this heater.

SAFETy INFORMATION

Continued

 WARNING: Do not allow fans 

to blow directly into the heater. 

Avoid any drafts that alter burner 

flame patterns. Ceiling fans can 

create  drafts  that  alter  burner 

flame  patterns.  Altered  burner 

patterns can cause sooting.

Due  to  high  temperatures,  the 

appliance should be located out 

of traffic and away from furniture 

and draperies.

Do not place clothing or other 

flammable  material  on  or  near 

the appliance. Never place any 

objects on the heater.

Heater base assembly becomes 

very hot when running heater. 

Keep children and adults away 

from hot surface to avoid burns 

or  clothing  ignition.  Heater 

will remain hot for a time after 

shutdown. Allow surface to cool 

before touching.

Carefully supervise young chil-

dren when they are in the room 

with heater. 

You  must  operate  this  heater 

with a fireplace screen in place. 

Make  sure  fireplace  screen  is 

closed before running heater.

Keep  the  appliance  area  clear 

and free from combustible ma-

terials, gasoline and other flam-

mable vapors and liquids.

Summary of Contents for SGS3124N





























Reviews: