background image

www.desatech.com

111347-01F

15

PRESSURE TESTING HEATER GAS 

CONNECTIONS

1.  Open equipment shutoff valve (see Figure 15, 

page 14).

2.  Open main gas valve located on or near gas 

meter for natural gas or open propane/LP 

supply tank valve.

3.  Make sure control knob of heater is in the OFF 

position.

4.  Check all joints from equipment shutoff valve 

to control valve (see Figures 16 and 17). Apply 

noncorrosive leak detection fluid to all joints. 

Bubbles forming show a leak.

5.  Correct all leaks at once.

6.  Light heater (see Operating Heater

, page 16) 

depending on your model). Check all other 

internal joints for leaks.

7.  Turn off heater (see To Turn Off Gas to Ap-

pliance

, page 18 or 20, depending on your 

model).

INSTALLATION

Continued

Figure 16 - Checking Gas Joints 

(Propane/LP only)

Gas Control 
Valve Location

Propane/LP 
Supply Tank

Equipment 
Shutoff Valve

Figure 17 - Checking Gas Joints (Natural 

Gas Only)

Gas Meter

Gas Control 
Valve Location

Equipment 
Shutoff Valve

Figure 18 - Rear Log Placement (Variable 

Manually-Controlled Models)

Rear Log

INSTALLING LOGS

 WARNING: Failure to position 

the parts in accordance with these 

diagrams  or  failure  to  use  only 

parts specifically approved with 

this heater may result in property 

damage or personal injury.

 CAUTION: After installation 

and  periodically  thereafter, 

check  to  ensure  that  no  flame 

comes in contact with any log. 

With the heater set to HI, check 

to see if flames contact any log. If 

so, reposition logs according to 

the log installation instructions 

in this manual. Flames contact

-

ing logs will create soot.

It is very important to install the logs exactly as 

instructed. Do not modify logs. Only use logs 

supplied with heater.

Variable Manually-Controlled Models 
(LSL)

1.  Place rear log onto rear brackets making sure 

brackets fit into recess on bottom of log (see 

Figure 18). 

2.  Place left front log on grate fingers as shown 

in Figure 19, page 16. Place right front log on 

grate fingers and on left front log (see Figure 

19, page 16).

3.  Slide control cover log into position between 

two front logs assuring the cover log seats into 

cutout section (see Figure 20, page 16).

Summary of Contents for CDL3924NT

































Reviews: