background image

www.desatech.com

111347-01F

7

ACCESSORIES

NOTICE:  All  accessories  may 

not be available for all fireplace 

models.

Purchase these heater accessories from your local 

dealer. If they can not supply these accessories, 

call DESA Heating Products at 1-866-672-6040 

for referral information. You can also write to the 

address listed on the back page of this manual.

EQUIPMENT SHUTOFF VALVE 
GA5010

For all models.

 Equipment shutoff valve with 1/8" 

NPT tap. Fits 1/2" NPT pipe. 

FIREPLACE HOOD

Black - GA6050

 

Brass - GA6052

 

Antique Brass - GA6053

For all models.

 Helps deflect heat away from 

mantel or wall above fireplace. Fits openings 28" 

to 48" wide.

DAMPER CLAMP - GA6080

 

(Not Shown)

For all models.

 Permanently opens chimney flue 

damper for vented operation.

LAVA ROCK - GA6060

 

(Not Shown)

For all models.

 Order when additional rock is 

desired. (1.8 lb. bag)

CLEANING KIT - GCK 

(Not Shown)

For all models.

 Your vent-free gas appliance re-

quires regular cleaning and maintenance to prevent 

performance problems. This kit gives you the tools 

and instructions to make it easy to clean all critical 

areas of your appliance.

INFORMATION VIDEO - 108917-01

For all models.

 A care and maintenance video is 

available by calling 1-866-672-6040. You may 

also email your request to

[email protected]

.

SERVICE HINTS

When Gas Pressure Is Too Low

•  pilot will not stay lit

•  burners will have delayed ignition

•  heater will not produce specified heat

•  for propane/LP units, propane/LP gas supply 

may be low

You may feel your gas pressure is too low. If so, con

-

tact your local propane/LP or natural gas supplier.

TECHNICAL SERVICE

You may have further questions about installation, 

operation or troubleshooting. If so, contact DESA 

Heating Products’ Technical Service Department 

at 1-866-672-6040. When calling please have your 

model and serial numbers of your heater ready.

You can also visit DESA Heating Products’ techni-

cal services web site at 

www.desatech.com

.

REPLACEMENT PARTS

Note:

 Use only original replacement parts. This 

will protect your warranty  coverage for parts 

replaced under warranty. 

PARTS UNDER WARRANTY

Contact authorized  dealers  of  this product. If 

they can’t supply original replacement part(s), 

call DESA Heating Products’ Technical Service 

Department at 1-866-672-6040.

When  calling  DESA  Heating  Products,  have 

ready

•  your name

•  your address

•  model and serial numbers of your heater 

•  how heater was malfunctioning

•  type of gas used (propane/LP or natural gas)

•  purchase date

Usually, we will ask you to return the part to the 

factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they 

can’t supply original replacement part(s), call 

DESA Heating Products at 1-866-672-6040 for 

referral information.

When  calling  DESA  Heating  Products,  have 

ready

•  model number of your heater 

•  the replacement part number

Summary of Contents for CDL3924NT

































Reviews: