background image

www.desatech.com

111347-01F

6

Capillary 

Thermostat 
Sensing Bulb 

Do Not Crimp 
Capillary 

Adhesive-
backed 
Mounting Clip 

Figure 37 - Positioning the Thermostat 

Sensing Bulb in the Vertical Position 

with the Capillary at the Bottom 

OPTIONAL POSITIONING 

OF THERMOSTAT 

SENSING bULb

Continued

SPECIFICATIONS

 

 

Echo Valley Oak Log

 

 

Variable Manually-Controlled

Btu (Variable) 

16,000/31,500

Type Gas 

Propane/LP - Natural

Ignition 

Piezo

Manifold Pressure 

8.0" W.C. - 3.5" W.C.

Inlet Gas Pressure (in. of water)

 

Maximum 

14" - 10.5"

 

Minimum* 

11" - 5"

Shipping Weight  

38 lbs.

* For purpose of input adjustment

 

 

Meadowbrook Oak Log

 

 

Thermostatically-Controlled

Btu (Variable) 

26,000/39,000

Type Gas  

Propane/LP - Natural

Ignition 

Piezo

Manifold Pressure  

8.0" W.C. - 3.5" W.C.

Inlet Gas Pressure (in. of water)

 

Maximum 

14" - 10.5"

 

Minimum* 

11" - 5"

Shipping Weight  

28 lbs.

* For purpose of input adjustment

4.  The mounting clip must be a minimum of 3" from 

bottom of fireplace to prevent crimping of capil

-

lary. Once you have decided on a location, clean 

the area thoroughly. Remove the paper backing 

from the adhesive on back of mounting clip. Press 

the clip into the new location so that the thermostat 

sensing bulb will be positioned vertically with the 

capillary at the bottom (see Figure 37). Slide the 

thermostat sensing bulb into the clip.

 

IMPORTANT: 

Do not crimp capillary. 

Summary of Contents for CDL3924NT

































Reviews: