6
103427
UNVENTED PROPANE GAS LOG HEATER
NOTICE: Manual control heaters
may be used as a vented product.
If so, you must always run heater
with chimney flue damper open.
If running heater with damper
open, non-combustible material
above fireplace opening is not
needed. Go to
Installing Damper
Clamp Accessory for Vented
Operation, page 8.
Minimum Non Combustible
Material Clearances
If Not Using Mantel
Note:
If using a mantel, go to page 7. If not
using a mantel, follow the information on
this page.
You must have non combustible material(s)
above the fireplace opening. Non combus-
tible materials (such as slate, marble, tile,
etc.) must be at least 1/2 inch thick. With
sheet metal, you must have non combustible
material behind it. Non combustible mate-
rial must extend at least 8" up (for all mod-
els). If non combustible material is less than
12", you must install the fireplace hood
accessory (24" and 30" models only). See
chart on page 7, column 1 and Figure 5 for
minimum clearances.
IMPORTANT:
If you cannot meet these
minimum clearances, you must operate
heater with chimney flue damper open. Go
to Installing Damper Clamp Accessory for
Vented Operation, page 8.
INSTALLATION AND
CLEARANCES
(Vent-Free Operation Only)
Figure 5 - Minimum Clearance to Wall and
Ceiling
WARNING: Maintain the mini-
mum clearances. If you can, pro-
vide greater clearances from
floor, ceiling, and adjoining wall.
LOG SIZING REQUIREMENTS
Log
Minimum Firebox Size
Size
Height
Depth Front Width
18"
17"
14"
20"
24"
17"
14"
26"
30"
17"
14"
32"
MINIMUM FIREPLACE
CLEARANCE TO
COMBUSTIBLE MATERIALS
Log Size
18", 24", 30"
Side Wall
16"
Ceiling
42"
Floor
5"
Carefully follow the instructions below. This
will ensure safe installation into a masonry
or U.L. listed manufactured fireplace.
Minimum Wall and Ceiling
Clearances (see Figure 5)
A. Clearances from the side of the fire-
place opening to any combustible wall
should not be less than 16 inches.
B. Clearances from the top of the fireplace
opening to the ceiling should not be less
than 42 inches.
42"
16"
INSTALLATION
NOTICE: A qualified service per-
son must install heater. Follow
all local codes.
WARNING: Before installing
in a solid fuel burning fireplace,
the chimney flue and firebox must
be cleaned of soot, creosote,
ashes and loose paint by a quali-
fied chimney cleaner. Creosote
will ignite if highly heated. In-
spect chimney flue for damage. If
damaged, operate heater with flue
damper closed.
WARNING: Seal any fresh air
vents or ash clean-out doors lo-
cated on floor or wall of fireplace.
If not, drafting may cause pilot
outage or sooting. Use a heat-
resistant sealant. Do not seal
chimney flue damper.
WARNING: Never install the
heater
• in a bedroom or bathroom un-
less installed as a vented ap-
pliance, see page 8
• in a recreational vehicle
• where curtains, furniture,
clothing, or other flammable
objects are less than 36 inches
from the front, top, or sides of
the heater
• in high traffic areas
• in windy or drafty areas
CAUTION: This heater cre-
ates warm air currents. These
currents move heat to wall sur-
faces next to heater. Installing
heater next to vinyl or cloth wall
coverings or operating heater
where impurities in the air (such
as tobacco smoke) exist, may
discolor walls.
IMPORTANT:
Vent-free heaters add mois-
ture to the air. Although this is beneficial,
installing heater in rooms without enough
ventilation air may cause mildew to form
from too much moisture. See Air for Com-
bustion and Ventilation, pages 4 and 5.
CHECK GAS TYPE
Use only propane gas. If your gas supply is
not propane, do not install heater. Call
dealer where you bought heater for proper
type heater.
NOTICE: State or local codes may
only allow operation of this appli-
ance in a vented configuration.
Check your state or local codes.
Continued
