manualshive.com logo in svg

Dentech AYRDYNE 4.0, Installation, Operation And Maintenance Manual

Share
Download
Dentech AYRDYNE 4.0 Installation, Operation And Maintenance Manual Download Page 35

www.ayrdyne.com

DISCHARGE

33

STATUS 

This text display shows the following 
conditions:

 Stopped

 

Rotary valve is stopped

 Running

 

Rotary valve is running

 

Over Load Tripped

 

Rotary valve is faulted on overload 

 condition

 

Zero Speed Tripped

 

Rotary valve is told to run but the Zero 

 

speed switch does not detect motion  

 

(if equipped)

 

 

Field Disconnect Open

 

Field Disconnect is open and rotary 

 

valve will not operate (if equipped)

OFF 
This button places the rotary valve in Off 

mode and prevents the rotary valve from 
running. This is not intended for servicing 
the rotary valve. Follow LOTO rules when 
servicing. rotary

AUTO 

This button places the rotary valve in Auto 
mode. When engaged, the rotary valve 
will run if the blower is running or during 
downtime cleaning. 

HAND 

This button places the rotary valve in Hand 
mode. When engaged and all interlocks are 
met, the rotary valve will run continuously.

SHUTDOWN SYSTEM ON ROTARY VALVE 
FAULT

This toggle enables a shutdown fault of the 
collector when the rotary valve has a fault 

condition. When switched off, the collector 

will continue to run, but a warning indicator 
will continue to display the active fault.

SHUTDOWN DELAY (m) 

This numeric entry/display shows the 
amount of time (in minutes) a rotary valve 
fault must be active before generating a 
fault.

1

5

2

3

6

4

2.4

OPERATION

a

b

c

d

e

Summary of Contents for AYRDYNE 4.0



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands