![background image](http://html1.mh-extra.com/html/denon/dnhd2500-dual-dj-mp3-player/dnhd2500-dual-dj-mp3-player_service-manual_2481151010.webp)
10
DN-HD2500
2.7
TOUCH_Init
mode
・
Turn the Deck1 or Deck2 PARAMETERS knob
to select "TOUCH_Init" from the FUNCTION
check mode's top menu, then press the
PARAMETERS knob to set "TOUCH_Init"
mode.
・
The detection level value and detection thresh-
old value stored in the EPROM in the touch
sensor's IC are rewritten with the factory
default values and the touch sensor IC is ini-
tialized.
When the process has completed normally,
"Complete!!" is displayed.
・
UP, R, DOWN and L display section
Displays the touch detection counter value
when the power is turned on.
・
Judge (70
〜
300) display section
"OK" is displayed if the touch detection
counter value when not being touched is
between 70 and 300. If not, "NG" [No Good] is
displayed.
・
Step1 display section
Displays the progress of the touch sensor IC's
initialization process.
1) Complete DECK1 Init
Indicates that reading of the touch detection
counter value when the Deck1 JOG disc is
not being touched is completed.
2) Complete DECK2 Init
Indicates that reading of the touch detection
counter value when the Deck2 JOG disc is
not being touched is completed.
3) Complete DECK1 Teaching
Indicates that "verify check" of the Deck1
touch detection system data (detection level
value and detection threshold value) is com-
pleted.
4) Complete DECK2 Teaching
Indicates that "verify check" of the Deck2
touch detection system data (detection level
value and detection threshold value) is com-
pleted.
5) DECK1 EEPROM Complete
Indicates that writing of the "verify check"
data for the Deck1 touch detection system is
completed.
6) DECK2 EEPROM Complete
Indicates that writing of the "verify check"
data for the Deck2 touch detection system is
completed.
When the process has completed abnormally,
"NG" [No Good] and "Fail (Check Touch
Device)" are displayed.
The touch device of the deck concerned, the
chip parts around the touch device and the
touch sensor unit of the side concerned must be
checked.
No
Mode
Operation and Function
Display
2.7
TOUCH̲Init
モード
・Deck1 または Deck2 の PARAMETERS ノブを回
わして、FUNCTION チェックモード画面から
TOUCH̲Init を選択し、PARAMETERS ノブを押
して確定します。
・タッチセンス IC 内の EPROM に記録されてい
る検出レベル値、検出スレッシュホールド値
を工場出荷時の値に書き換え、タッチセンス
IC を初期化します。
正常終了時、Complete!! を表示します。
・UP、R、DOWN、L の表示部
電源投入時のタッチ検出カウンタ値を表示し
ます。
・Judge(70 〜 300) 表示部
非タッチ時のタッチ検出カウンタ値が、70 〜
300 の範囲にある時 OK を表示します。 範囲外
の時は、NG を表示します。
・Step1 表示部
タッチセンス IC 初期化処理の進行度を表示し
ます。
① Complete DECK1 Init
DECK1 の JOG ディスク非タッチ時のタッチ
検出カウンタ値読み出し終了を示します。
② Complete DECK2 Init
DECK2 の JOG ディスク非タッチ時のタッチ
検出カウンタ値読み出し終了を示します。
③ Complete DECK1 Teaching
DECK1 のタッチ検出システム用データ ( 検
出レベル値、検出スレッシュホールト値 )
のベリファイチェック終了を示します。
④ Complete DECK2 Teaching
DECK2 のタッチ検出システム用データ ( 検
出レベル値、検出スレッシュホールト値 )
のベリファイチェック終了を示します。
⑤ DECK1 EEPROM Complete
DECK1 のタッチ検出システム用ベリファイ
データの書き込み終了を示します。
⑥ DECK2 EEPROM Complete
DECK2 のタッチ検出システム用ベリファイ
データの書き込み終了を示します。
異常終了時、NG と Fail (Check Touch Device) を
表示します。
該当する DECK のタッチデバイス、タッチデバ
イス周辺のチップ部品及び、該当側のタッチセ
ンサーユニットのチェックが必要です。
No
モード
操 作 と 機 能
表 示
Summary of Contents for DNHD2500 - Dual DJ MP3 Player
