SECTION 3
3-1
01/01/2013
ELECTRICAL - FUEL HOOK-UP AND CHECKOUT
1.
POWER SUPPLY
AN ADEQUATE POWER SUPPLY AND PROPER WIRING ARE IMPORTANT FOR MAXIMUM
PERFORMANCE AND LONG DRYER LIFE.
ELECTRICAL SERVICE MUST BE ADEQUATE IN
SIZE TO PREVENT LOW VOLTAGE DAMAGE TO MOTORS AND CONTROL CIRCUITS.
PROPER
LINE PHASING MUST ALSO BE OBSERVED.
2.
POWER SUPPLY CIRCUIT BREAKER
ALL DELUX GRAIN DRYERS SHOULD BE EQUIPPED WITH A MASTER CIRCUIT
DISCONNECT TO PERMIT TOTAL SHUT-DOWN OF THE DRYING SYSTEM.
IT IS SUGGESTED
THAT ALL WET AND DRY HANDLING EQUIPMENT BE INTERLOCKED THROUGH MASTER
CIRCUIT DISCONNECT. CALCULATE TOTAL AMP. LOAD OF SYSTEM TO MAKE SURE LOAD
DOES NOT EXCEED DISCONNECT RATING.
3.
TRANSFORMERS - WIRE - VOLTAGE DROP
CONTACT THE SERVICE REPRESENTATIVE OF YOUR LOCAL POWER COMPANY TO
ADVISE OF ADDITIONAL LOAD TO BE PLACED ON THE LINE.
CHECK ON KVA RATING OF
TRANSFORMERS, CONSIDERING TOTAL H.P. LOAD. THE POWER SUPPLY WIRING AND
TRANSFORMERS MUST BE CAPABLE OF PROVIDING ADEQUATE MOTOR STARTING AND
OPERATING VOLTAGE.
4.
CONSIDERING TOTAL H.P. LOAD
AND DISTANCE FROM TRANSFORMER, SIZE AND
INSTALL WIRE AND CONDUIT BETWEEN TRANSFORMER AND DRYER ELECTRICAL SERVICE
CENTER.
*NOTE: MAKE SURE DRYER IS ADEQUATELY GROUNDED.
5.
CONDUIT INSTALLATION
GARNER BIN HIGH GRAIN SHUTDOWN, LOW GRAIN SHUTDOWN CONTROLS AND THE
LEVELING AUGER MOTOR ARE SUPPLIED WITH CONDUIT AND WIRING, REFER TO DRAWING
OF GARNER.
6.
INTERNAL FUEL LINE HOOK-UP
THE DRYER IS EQUIPPED WITH A PLUMBING TRAIN CONTAINING SAFETY
CONTROLS.
REFER TO DRAWINGS OF FUEL LINE HOOK-UP FOR ALL MODELS.
7.
FUEL SUPPLY
(REFER TO SECTION 5 OF SERVICE MANUAL FOR "FUEL SUPPLY RECOMMENDED").
CONTACT YOUR LOCAL FUEL SUPPLIER FOR PROPER SIZING OF REGULATORS AND
PLUMBING.
8.
FLAME ROD(S) AND SPARK IGNITER ADJUSTMENT
CHECK BURNER FLAME ROD(S) AND SPARK IGNITER ADJUSTMENT.
A.
THE FLAME ROD(S) SHOULD BE CHECKED TO SEE THAT THE CERAMIC BASE
HAS NOT BEEN CRACKED. CHECK SPARK IGNITER: (SHOULD HAVE 1/8" TO
3/16" GAP).
Summary of Contents for DPX12T
