background image

7 Installation

Safety instructions

54

7. 

Installation

 

Read chapter “5. Planning the installation”, 

page 27 and this chapter in full before 

you start installation.

7.1  Safety instructions

DANGER 

Electric shock

Potentially fatal voltages are present in the 

inverter during operation. When the inverter 

is disconnected from all power sources, this 

voltage remains in the inverter for up to 60 

seconds. 

You should therefore always carry out the fol-

lowing steps before working on the inverter:
1.  Turn both DC isolating switches to the 

OFF

 

position.

2.  Disconnect the inverter from all AC and DC 

voltage sources and make sure that none 

of the connections can be restored acciden-

tally.

3.  Wait at least 60 seconds for the internal 

capacitors to discharge.

DANGER

Electric shock

Potentially fatal voltages are present at the DC 

connections of the inverter. When light falls on 

the solar modules, they immediately start to 

generate electricity. This also happens when 

light does not fall directly on the solar modules.

 

Never disconnect the inverter from the solar 

modules when it is under load. 

 

Turn both DC isolating switches to the 

OFF

 

position.

 

Disconnect the connection to the grid so that 

the inverter cannot feed energy into the grid. 

 

Disconnect the inverter from all AC and DC 

voltage sources. Make sure that none of the 

connections can be restored accidentally.

 

Ensure that the DC cables cannot be 

touched accidentally.

DANGER

Electric shock

The inverter has a high leakage current value.

 

Always

 connect the ground cable first, then 

the AC and DC cables.

WARNING

Electric shock

If the doors of the inverter are open, the IP65 

degree of protection is no longer guaranteed.

 

Only open the door when absolutely 

necessary.

 

Do not open the door if water or dirt might 

enter the inverter. 

 

After work is completed, ensure that the 

door is properly shut and tightened again. 

Check that the door is properly sealed.

WARNING

Heavy weight

The inverter is heavy.

 

Lift and carry the inverter with at least 2 

people.

NOTICE

Water ingress.

 

All sealing caps removed during installation 

should be stored for later use (e.g.  trans-

portation or storage).

Installation and Operation Manual for Solar Power Inverter M70A EU V2.0 EN 2020-06-22

Summary of Contents for M70A 260









































































































































































































Reviews: