Dell Vostro 3480 Service Manual Download Page 28

Page: 28 / 93

Removing the M.2 2280 Solid-state drive or Intel Optane
memory - Optional

Prerequisites

Follow the procedure in

before working inside your computer

Remove the

SD memory card

Remove the

base cover

Remove the

battery

Steps

Loosen the captive screw that secures the thermal plate to the palmrest and keyboard assembly [1].

Remove the single (M2x3) screw that secures the thermal plate to the palmrest and keyboard assembly [2].

Slide and remove the thermal plate from the solid-state drive/Intel Optane slot [3].

Slide and lift the solid-state drive/Intel Optane off the palmrest and keyboard assembly [4].

Installing the M.2 2280 Solid-state drive or Intel Optane
memory - Optional

Steps

Slide and insert the tab solid-state drive/Intel Optane into the solid-state drive/Intel Optane slot [1, 2].

Tighten the captive screw that secures the thermal plate to the palmrest and keyboard assembly [3].

Replace the single (M2x3) screw that secures the thermal plate to the palmrest and keyboard assembly [4].

Removing and installing components

Summary of Contents for Vostro 3480






























































































Search results

Summary of Contents for Vostro 3480

Reviews:

Related manuals for Vostro 3480

Brands by name

Popular brands

Dell Vostro 3480, Service Manual

Search results

Summary of Contents for Vostro 3480

Reviews:

Related manuals for Vostro 3480

Brands by name

Popular brands