Dell Vostro 3480 Service Manual Download Page 14

Page: 14 / 93

Removing and installing components

Recommended tools

The procedures in this document require the following tools:

•

Phillips #0 screwdriver

•

Phillips #1 screwdriver

•

Plastic scribe

NOTE:

The #0 screw driver is for screws 0-1 and the #1 screw driver is for screws 2-4

Screw list

The table provides the list of screws that are used for securing different components.

Table 3. Screw list

Component

Screw type

Quantity

Screw image

Base cover

M2.5x6

NOTE:

Screw color may vary

depending on the
configuration ordered.

Battery

M2x3

Display panel

M2x2

System Fan

M2x5

VGA daughterboard

M2x3

Hard-drive assembly

M2x3

Hard-drive bracket

M3x3

Heat sink - discrete

M2x3

Hinges

M2.5x2.5

Removing and installing components

Summary of Contents for Vostro 3480






























































































Search results

Summary of Contents for Vostro 3480

Reviews:

Related manuals for Vostro 3480

Brands by name

Popular brands

Dell Vostro 3480, Service Manual

Search results

Summary of Contents for Vostro 3480

Reviews:

Related manuals for Vostro 3480

Brands by name

Popular brands