Dell Vostro 3401 Service Manual Download Page 80

Page: 80 / 87

Steps

1. Align and place the system board on the palmrest.
2. Replace the single (M2x4) screw that secures the system board to the palmrest.

3. Connect the following cables to the system board:

a. Speaker cable
b. Keyboard FFC
c. Keyboard backlight FFC
d. Touchpad FFC
e. Hard drive FFC
f. IO board FFC
g. Power adapter port cable
h. Fingerprint reader FFC
i.

Power button FFC from the system board

4. Fold back the right hinger and install the two (M2.5x5) screws to secure it to the palmrest.

Next steps

1. Install the

2. Install the

3. Install the

4. Install the

5. Install the

6. Install the

7. Install the

8. Install the

9. Install the

10. Follow the procedure in

after working inside your computer

Power-adapter port

Removing the power adapter port

Prerequisites

1. Follow the procedure in

before working inside your computer

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

8. Remove the

9. Remove the

NOTE:

The system board can be removed along with the heat sink.

Disassembly and reassembly

Summary of Contents for Vostro 3401
























































































Search results

Summary of Contents for Vostro 3401

Reviews:

Related manuals for Vostro 3401

Brands by name

Popular brands

Dell Vostro 3401, Service Manual

Search results

Summary of Contents for Vostro 3401

Reviews:

Related manuals for Vostro 3401

Brands by name

Popular brands