Dell Vostro 3401 Service Manual Download Page 28

Page: 28 / 87

About this task

Steps

1. Align the tabs on the battery with the slots on the palm rest assembly.

NOTE:

When installing the battery into the system, insert the tab at the bottom left corner of the battery into the hook

on the bottom side of the palm rest.

2. Replace the three (M2x3) screws that secure the battery to the palmrest.
3. Reconnect the battery cable to the connector on the system board.

NOTE:

When installing the battery into the system, insert the tab at the bottom left corner of the battery into the hook

on the bottom side of the palm rest.

Next steps

1. Install the

base cover

2. Install the

SD card

3. Follow the procedure in

after working inside your computer

Disassembly and reassembly

Summary of Contents for Vostro 3401
























































































Search results

Summary of Contents for Vostro 3401

Reviews:

Related manuals for Vostro 3401

Brands by name

Popular brands

Dell Vostro 3401, Service Manual

Search results

Summary of Contents for Vostro 3401

Reviews:

Related manuals for Vostro 3401

Brands by name

Popular brands