Dell Vostro 3401 Service Manual Download Page 53

Page: 53 / 87

2. Unthread the display cable and WLAN antenna cables from the routing channels.
3. Open the system to at least 90-degrees and place the system on the edge of a table so that the palm rest is laying flat on

the table and the display assembly is over the edge.

4. Remove the four (M2.5x5) screws securing the display assembly in place.
5. Remove the display assembly from the system.

Installing the display assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE:

Ensure that the hinges are opened to the maximum before replacing the display assembly on the palmrest and

keyboard assembly.

Disassembly and reassembly

Summary of Contents for Vostro 3401
























































































Search results

Summary of Contents for Vostro 3401

Reviews:

Related manuals for Vostro 3401

Brands by name

Popular brands

Dell Vostro 3401, Service Manual

Search results

Summary of Contents for Vostro 3401

Reviews:

Related manuals for Vostro 3401

Brands by name

Popular brands