Dell S6100 Installation Manual Download Page 3

Page: 3 / 54

Contents

1 About this guide............................................................................................................................................. 5

Notices................................................................................................................................................................................ 5
Related documents............................................................................................................................................................ 5

2 S6100–ON system.........................................................................................................................................6

LED behavior ............................................................................................................................................................... 9

Prerequisites.......................................................................................................................................................................11
S6100–ON configurations............................................................................................................................................... 12

3 Site preparations.......................................................................................................................................... 13

Fan combinations........................................................................................................................................................14

Power................................................................................................................................................................................. 14
Storing components......................................................................................................................................................... 15

4 NEBS compliance.........................................................................................................................................16

Important information...................................................................................................................................................... 16
NEBS-compliant ground installation...............................................................................................................................16

For rack spans from 22 to 23.375 inches.................................................................................................................17
For rack spans from 23.375 to 36 inches................................................................................................................ 19

5 S6100–ON installation................................................................................................................................. 23

Important points.........................................................................................................................................................28

Contents

Summary of Contents for S6100























































Search results

Summary of Contents for S6100

Reviews:

Related manuals for S6100

Brands by name

Popular brands

Dell S6100, Installation Manual

Search results

Summary of Contents for S6100

Reviews:

Related manuals for S6100

Brands by name

Popular brands