Dell S4248FB-ON Installation Manual Download Page 4

Page: 4 / 47

Optics installation.............................................................................................................................................................28

Optics removal............................................................................................................................................................28

Switch power-up..............................................................................................................................................................28

Power up sequence................................................................................................................................................... 29

After switch installation...................................................................................................................................................29
Switch replacement.........................................................................................................................................................29

6 Power supplies............................................................................................................................................ 30

Components..................................................................................................................................................................... 30

PSU LEDs.................................................................................................................................................................... 31

AC or DC power supply installation................................................................................................................................ 31

AC or DC power supply replacement...................................................................................................................... 32

Connect DC power supply to power source.................................................................................................................32

7 Fans.............................................................................................................................................................34

Components..................................................................................................................................................................... 34

Fan LEDs.....................................................................................................................................................................35

Fan module installation....................................................................................................................................................35

Fan module replacement...........................................................................................................................................35
Fan air filter replacement.......................................................................................................................................... 36

8 Management ports.......................................................................................................................................37

Example of the Grub Bootloader............................................................................................................................. 39
Example of ONIE........................................................................................................................................................39

ONIE service discovery................................................................................................................................................... 39

9 Specifications...............................................................................................................................................41

Emissions.................................................................................................................................................................... 45
Immunity..................................................................................................................................................................... 45

Safety standards and compliance agency certifications.............................................................................................45
Product recycling and disposal.......................................................................................................................................46

Waste Electrical and Electronic Equipment (WEEE) directive for recovery, recycle, and reuse of IT and
telecommunications products.................................................................................................................................. 46

10 Dell EMC support....................................................................................................................................... 47

Contents

Summary of Contents for S4248FB-ON
















































Search results

Summary of Contents for S4248FB-ON

Reviews:

Related manuals for S4248FB-ON

Brands by name

Popular brands

Dell S4248FB-ON, Installation Manual

Search results

Summary of Contents for S4248FB-ON

Reviews:

Related manuals for S4248FB-ON

Brands by name

Popular brands