background image

Table 6. Environmental parameters

Parameter

Specifications

Operating temperature

0°C to 45°C (32°F to 113°F) continuously
-5°C to 45°C (23°F to 113°F) short term

Short term is </= 1% of operational hours per year.

NOTE: 

Reduce maximum temperature by 1°C/300 meters 

(1°F/547 feet) above 950 meters (3,117 feet).

Operating humidity

5% to 85% (RH), non-condensing, continuously
5% to 90% (RH), non-condensing, short term

Short term is </= 1% of operational hours per year.

Storage temperature

–40° to 70°C (–40° to 158°F )

Storage humidity

5% to 95%, non-condensing

Maximum thermal output

600 W = 2047 BTU/Hr

Maximum operational altitude

10,000 feet (3,048 meters)

Maximum non-operational altitude

39,370 feet (12,000 meters)

Shock

Dell EMC Spec SV0115

Table 7. AC power requirements

Parameter

Specifications

Power supply

100–240 VAC 50/60 Hz

Maximum current draw per system

6A/5A at 100/120V AC 3A/2.5A at 200/240V AC

Maximum power consumption

600 Watts

Typical power consumption

300 Watts

Table 8. DC power requirements

Parameter

Specifications

Minimum and maximum input voltage range

−40.5, –60V DC, 15A Max

Maximum power consumption

600 Watts

Start up VDC

39.0 ± 1.5 V

Start off VDC

37.5 ± 1.5 v

IEEE standards

The S4200-ON Series (S4248FB-ON and S4248FBL-ON) switch complies with the following IEEE standards:

802.1ab (LLDP)

802.1ax (Layer 2)

802.1d, 802.1w, 802.1s, 802.1x (Mgmt/Security), 802.3x (Layer 2)

802.3 (1000BASE-KX)

42

Specifications

Summary of Contents for S4248FB-ON
















































Reviews: